âoÃuÃ�´2) Adjust the stapling position by pressing the PSW1 or PSW2 on
[8] ADJUSTMENTSService Manual
the finisher controller PCB a required number of times. Press-
ing the switch once moves the stapling position about 0.14
1. Finisher/saddle unitmm.
? To move the stapling position in the "-" direction, press the
A. Adjusting the Folding Position
PSW1.
The folding position is adjusted by matching it with the stapling
? To move the stapling position in the "+" direction, press the
position.
PSW2.
If you have replaced the finisher controller PCB, you must transfer
? Pressing the PSW1 and PSW2 at the same time clears the
the existing settings to the new PCB. Perform the following if the
adjustment value.
folding position must be adjusted for some reason.
NOTE: Both the folding and stapling positions may deviate for
some type of paper. In such a case, change the "middle- direction+ direction
stapling position" in the user mode of the host machine.
1) Set SW1 on the finisher controller PCB as follows:
ON
1234 5678
2) Adjust the folding position by pressing the PSW1 or PSW2 on
the finisher controller PCB a required number of times. Press-
ing the switch once moves the folding position about 0.16 mm.
? To move the folding position in the "-" direction, press the3) When adjustment of the stapling position is complete, set all
PSW1.bits of the SW1 on the finisher controller PCB to OFF.
? To move the folding position in the "+" direction, press the4) Enter the bind mode of the host machine and check whether
PSW2.the stapling position is adjusted properly. If adjusted improp-
erly, adjust the stapling position again.
? Pressing the PSW1 and PSW2 at the same time clears the
adjustment value.C. One-page exit mode
This mode is used to increase the accuracy of paper alignment in
the simple load offset mode by discharging paper one by one to the
- direction+ direction
offset tray.
1) Set the SW1 of the finisher control PWB as shown below.
ON
1234 5678
2) Turn on the power.
3) When adjustment of the folding position is complete, set all bits2. Punch unit (option)
of the SW1 on the finisher controller PCB to OFF.
A. Adjusting the Punch Hole Position
4) Enter the bind mode of the host machine and check whether
This adjustment is available only in the diagnostic mode (Sim 3-10)
the folding position is adjusted properly. If adjusted improperly,
of the host machine. The range of punch hole displacement is
adjust the folding position again.
between 3 and -3 in 1-mm increments. A higher setting will move
B. Adjusting the Middle 2-Point Stapling Positionthe punch hole toward the leading edge of sheet.
The stapling position is adjusted by matching it with the folding
B. Adjusting the Sensor Output
position.
Perform the following when the punch controller PCB, horizontal
This adjustment is necessary:
registration sensor (photosensor PCB/LED PCB), or waste full sen-
? If you have replaced the finisher controller PCB.
sor (waste full photosensor PCB/waste full LED PCB) has been
? If the stapling position must be adjusted for some reason.replaced.
NOTE: Both the folding and stapling positions may deviate for1) Shift bits 1 through 4 on the punch controller PCB as follows:
some type of paper. In such a case, change the "middle
stapling position" in the user mode of the host machine.ON
1) Set SW1 on the finisher controller PCB as follows:
ON1234
2) Press SW1002 or SW1003 on the punch controller PCB. A
press will automatically adjust the sensor output.
1234 5678
? The adjustment is over when all LEDs on the punch control-
ler PCB are ON: LED1001, LED1002, LED1003.
3) Shift all bits of DIPSW1001 to OFF.
MX-FNX2/AR-PN1/MX-RBX1 ADJUSTMENTS 8 - 1 |
ACEC
