CD-BA250H/CD-BA2600H
Troubleshooting Chart
Many potential "problems" can be resolved by the owner without calling a service
Cassette deck
technician.
If something is wrong with this product, check the following before calling your author-
SymptomPossible cause
ised SHARP dealer or service centre.
Cannot record.Is the erase-prevention tab removed?
Cannot record tracks with properIs it a normal tape? (You cannot record on
General
sound quality.ametal or CrO tape.)
SymptomPossible causeCannot erase completely.
The clock is not on time.Did a power failure occur? Reset theSound skipping.Is there any slack?
clock.Is the tape stretched?
When a button is pressed, the unitSet this unit to the power stand-by mode Cannot hear treble.Are the capstans, pinch rollers, or heads
does not respond.and then turn it back on.dirty?
Sound fluctuation.
If the unit still malfunctions, reset it. Refer
Cannot remove the tape.If a power failure occurs during playback,
to step 3 under "If trouble occurs"
the heads remain engaged with the tape.
No sound is heard.Is the volume level set to "0"?Do not open the compartment forcibly.
Are the headphones connected?Wait until electricity resumes.
Are the speaker wires disconnected?
Remote control
CD playerSymptomPossible cause
The remote control does not oper-Is the AC power lead of the unit plugged
SymptomPossible causeate.in?
Playback does not start.Is the disc loaded upside down?Is the battery polarity respected?
Playback stops in the middle or isDoes the disc satisfy the standards?Are the batteries dead?
not performed properly.Is the distance or angle incorrect?
Is the disc distorted or scratched?
Playback sounds are skipped, orIs the unit located near excessive vibra-Does the remote control sensor receive
stopped in the middle of a track.tions?strong light?
Is the disc very dirty?
Condensation
Has condensation formed inside the unit?
Sudden temperature changes, storage or opera-
tion in an extremely humid environment may
Tunercause condensation inside the cabinet (CD pick-
up, tape heads, etc.) or on the transmitter on the
SymptomPossible causeremote control.
Condensation can cause the unit to malfunction.
Radio makes unusual noise con-Is the unit placed near the TV or compu-
If this happens, leave the power on with no disc
secutively.ter?
(or cassette) in the unit until normal playback is
Is the FM aerial or AM loop aerial placedpossible (about 1 hour). Wipe off any condensa-
properly? Move the AC power lead awaytion on the transmitter with a soft cloth before op-
from the aerial if located near.erating the unit.
Troubleshooting ChartRemote Control
If trouble occursTest of the remote control
When this product is subjected to strong external interference (mechanical shock,Face the remote control directly to the remote sensor on the unit.
excessive static electricity, abnormal supply voltage due to lightning, etc.) or if it is
operated incorrectly, it may malfunction.
The remote control can be used within the range shown below:
If such a problem occurs, do the following:Press the ON/STAND-BY button. Does the power turn on? Now, you can enjoy the
music.1 Set the unit to the stand-by mode and turn the power on again.
2 If the unit is not restored in step 1, unplug and plug in the unit, and then turn
the power on.
3 If neither step 1 nor 2 restores the unit, do the following:
Press the ON/STAND-BY button to enter the power stand-by mode.Remote sensor
Whilst pressing down the / button and the X-BASS/DEMO button, press
the ON/STAND-BY button until "CLEAR AL" appears.
0.2 m - 6 m
Caution:(8" - 20')
This operation will erase all data stored in memory including clock, timer settings,
tuner preset, and CD programme.
Before transporting the unit
1 Press the ON/STAND-BY button to turn the power on.
2 Press the CD button.
3 Press the OPEN/CLOSE button to open the disc tray.
Remove all CDs inserted in the unit.
4 Press the OPEN/CLOSE button to close the disc tray.
Make sure that "NO DISC" is displayed.
5 Press the ON/STAND-BY button to enter the stand-by mode, and then unplug
the AC power lead from the AC socket.
� 7 � |
ACEC
