CD-E200H
* Press "PRESET UP" button or "PRESET DOWN" button after completion to obtain the following display.
CH displayFrequency displayLongitudinal display of PS name is possible.
(for 2 seconds)(for 2 seconds)(The same as in case of Ordinary)
NO PS
(Blinking for 5 seconds: 1 Hz)
Note: If PS is fixed after the frequency display is resumed
in case of NO PS display, the PS name is displayed.
* If signal exists at 106.50 MHz, the following indication appears.
FM 106.50 MHzPS nameWhen the PS data is given in case of NO PS display, the PS
name is displayed.
NO PS
(Blinking for 5 seconds: 1 Hz)
Note: If PS is fixed after the frequency display is resumed
in case of NO PS display, the PS name is displayed.
In case of memory storage with ASPM, for example, if RDS station 107.50 MHz has the PI code (the same as that of RDS
station 105.50 MHz) and VSM is larger than 105.50 MHz (PR-01), data is overwritten on 105.5 MHz that is contained in "PR-
01". (Frequency is changed to 107.50 MHz at "PR-01".)
If VSM is equal, previously stored 105.50 MHz remains.
When storing RDS station in the test mode, preset numbers do not blink for 2 seconds in order to save the production line
test time. ("RDS" lights up.)
Note: RDS is operated in FM MONO state. However, in case of ASPM, ASPM scan is operated after BAND is changed from
FM MONO to FM STEREO.
Note: Press the STOP button in TEST 2 mode to check the state of IF count. Since this function is for designer, it is not
necessary for other sections.
B) Cautions concerning the ASPM test mode
a) Cancel: Press the "FUNCTION" button again during operation after pressing it at first in the test mode to cancel (interrupt)
the ASPM test mode and to restore the initial state FM 106.50 MHz (ST) display.
(If the test mode is interrupted, use the preset UP/DOWN button to check the data preset and stored until interruption.)
b) The ASPM test mode starts in FM stereo state (FM 106.50 MHz ST). When pressing any button other than FUNCTION
button only once after it starts, it becomes invalid. Thus the ASPM test mode becomes inoperable.
Invalid: The Ordinary mode is obtained while 4 to 30CH data remain in memory (or 1 to 30 CH MAX data remain in memory).
The "FUNCTION" button can be repeatedly operated until 01CH to 03CH is filled (up to 3 stations in memory).
The number of stored stations -> Channel No. -> Frequency -> FM 106.50 MHz (ST) is displayed.
(1 second) (1 second) (1 second) (Initial state)
Max, 3 stations (CH1 to 3) can be displayed in ASPM mode.
In the modes other than ASPM mode, the number of stations
stored and then 'END' are displayed. Be careful of this point.
c) Broadcast (without PI code) which is not RDS is not preset and stored in memory.
When the ASPM mode is obtained, the "MEMORY/SET" button cannot be operated. (Test mode is canceled).
Operation is possible after ASPM test mode operation.
d) Scan frequency: 105.00 MHz -> 108.00 MHz
Data are stored in memory by monitoring the PI code and VSM (S meter value) so that the PI code is not duplicated. When
the PI code is duplicated, both VSM (S meter value) are compared. The larger one is stored in memory but the smaller
one is discarded.
For the stations having the same PI code, only one station with the highest electric field intensity is stored, and the memory
is refilled.
The channels that can be preset in the ASPM test mode are 01 to 03CH. If 3 stations are stored, 30 CHs are filled.
For the stations with the same electric field intensity, the former (preceding station) is stored.
For the stations having the same electric field intensity, the former (preceding station) is stored.
e) Already stored signals with same frequency are not stored. (The previously stored data is kept.)
f) The order of preset memory is 01CH -> 02CH -> 03CH.
� 16 � |
ACEC
