?Replace the memory backup battery at least once every 5 years. Record the
3. Overhead projector
date the memory backup battery was replaced to estimate the next
(1) The OHP projection panel is designed to be used only with a penetrationreplacement date.
style projector (one whose projector is located underneath).When nothing is displayed even though the ON key is pressed or if the
?The product cannot be used with reflection style projectors.operating batteries replacement message is displayed, the main batteries
?Set the light power to less than 700W when using a high light projectormay be depleted. In that case, replace the main batteries first.
(one whose light power is over 700W).If the memory backup battery is replaced while the main batteries are de-
?This product cannot be used with projectors using metallic halogen light.pleted, the memory contents of the OHP panel controller may be lost.
Doing so makes the OHP projection panel temperature extremely high?Please refer to the EL-9400/9600 operation manual to find out how to replace
and can result in device malfunction.the operation batteries and memory backup batteries.
5-2. Precautions on battery use
[Battery Handling Notes]
Batteries, it misused, can explode or cause electrolyte leakage. Pay special
attention to the following points:
1. Be sure to replace all four dry batteries at the same time.
2. Do not use new batteries with used batteries in the same unit.
(Penetration style)(Reflection style)
3. Replacement batteries should be of the same type as those to be replaced.
Some type of batterise are rechargeable, while other types are not. Carefully
(2) When using an overhead projector with a zoom function, set the overhead
projector stage to the lowest position.read the type description on the battery and choose the unrechargeable
type.
Setting the stage in a higher position makes the OHP projection panel
temperature extrmely high and can result in device malfunction.4. Insert the batteries in the correct orientations as indicated in the battery
compartments.
Caution:? Keep batteries out of the reach of children.
4. AC adapter
?Remove used batteries from the compartment. Otherwise, the
AC adaptor EZ-28A (included in products for the U.S.A. and Canada, optionalcomputer may be damaged from electrolyte leakage.
for other areas) can be used with the OHP projection panel. By using this ? ACDo not throw batteries into a fire as this may result in an explore.
adaptor, the operating battery consumption of the OHP panel controller can be
?The original batteries were installed at the factory at the time of
reduced.
shipment and may be depleted before satisfying the full operating
?Connect the AC adaptor after turning off the power of the OHP paneltime indicated in the specifications.
controller.
(Connect to the terminal on the right side (the cable side) of the OHP projec-
6. Reset
tion panel.)
If this product is exposed is exposed to powerful external electric field or shock
during use, an abnormal condition may seldom occur in which all of the keys,
including the ON key, do not function . In the event of such a situation reset it
as follows.
[How to reset]
Press the RESET switch only in the following cases.
AC adaptor?When an abnormal condition occurs and all the keys are inoperative.AC adaptor
connector?To clear all memory contents.
1) Press the RESET switch on the back of the OHP panel controller.
4-1. Precautions on AC adaptor use
?Use only AC adaptor EA-28A.
Not doing so may cause damage.
?Do not AC adaptor EA-28A for other equipment.
Doing so may cause damage to that equipment.?Please use a ball-point pen when pressing the RESET switch. Do not use a
?Turn off the power to the OHP panel controller before unplugging the ACsharp point or fragile object such as a needle, a mechanical pencil, etc.
adaptor from the AC adaptor connector.
2) The display should be as shown below. press the RESET switch again if the
?When not in use, unplug the AC adapter from the power outlet and from the
display is different from what is shown below.
AC adapter connector.
PRESS [CL] KEY TO
5. Power supplyPRESS ALL DATA
PRESS [CL] KEY TO
The OHP panel controller included with this product requires two kinds of batter-CANCEL
ies, one for its operation and the other for its memory backup. Please install all
four included batteries before the first usage. Please refer to the EL-9400/9600
operation manual to find out how to install the operation batteries. (The display shown is for the EL-96T OHP panel controller.)Note that the
memory backup battery has been installed at the factory at the time of shipment.3) To keep the memory contents:
Press ON . The display will return to the antinial display.
5-1. When the batteries need to be replaced4) To clear all memory contents:
?The following conditions indicate that the main batteries are depleted.Press CL while the above is being displayed. All memory contents will be
cleared and the display will become as follows.
1) Nothing is displayed even if the ON key is pressed.
2) The power suddenly goes off in the middle of operation.
ALL DATA CLEARED
3) The batteries replacement message is displayed.
Replace the batteries immediately if any one of these conditions occurs.PRESS ANY KEY
(The display shown is for EL-96T OHP panel controller.)
Pressing any key at this point restores the initial display. |
ACEC
