4. If you are using Windows 3.1 or Windows for Workgroups 3.1x:5-6. About Installing and Using WinFax Lite
Choose File from the Menu bar in the Program Manager, and
Winfax Lite is a fax software package that can be used with your unit.
then choose the Run... command.To install Winfax Lite, use the installation floppy disks that are in-
If you are using Windows 95:cluded with the unit. For more information regarding installation as
Click the Start button and then choose Run icon.well as general information about the software, please refer to the
5. Type a:\setup or b:\setup (depending on which drive is your 3.5"Winfax Lite user's manual.
floppy disk drive) in the command line box, and then click the OK
button.5-7. Turning on Printer Manager
6. Follow the instructions which appear in the installation window.In Windows 3.1 and Windows for Workgroups 3.1x, Printer Manager
Select Express, Compact or Custom in the Setup Type dialogstores print jobs on your hard disk, and then sends them to the printer
box. For details on each of these three installation methods, referin a predetermined order. This allows you to resume your work more
to "Express, Compact and Custom Installation" in this chapter.quickly. In particular, if you receive a fax in the middle of a print job,
7. Continue to follow the instructions which appear in the installationthe fax will be printed before the remaining pages of the print job. If
window.Print Manager is not on, however, you will have to wait until the print
job is complete before the fax is printed out. For this reason, we
8. Remove the floppy disk from the disk drive, and then click therecommend that you keep Print Manager on.
Restart button. When the Installation is Complete dialog box
appears in the display, click on the Close button to complete theFollow these steps to turn Print Manager on:
installation process.1. Double-click the Control Panel icon in the Main program group of
Program Manager, and then double-click the Printers icon. The
5-4. Express, Compact and Custom InstallationPrinters dialog box will open.
When you install the MFP Software, you are given the choice of2. Check the Use Printer Manager box by clicking it, if it is not
already checked.
installing all files in the system (Express), the minimum necessary
files (Compact), or only the files you specify (Custom).3. Click the Close button (click the Cancel button if you didn't
Express:change any settings).
Express installation will install all files, including Office WorkTop, Of-
fice WorkTop Help, F-3600M Help, the PCL Emulation Front Panel,5-8. Changing Virtual Memory Settings
and the F-3600M Control Panel. Full installation requires ap-Virtual memory is the space on the hard disk which your computer
proximately 5 MB of free hard disk space.uses as if it were random access memory (random access memory,
Compact:or RAM, is the working memory your computer uses to run applica-
tions, etc.). Virtual memory allows you to work with files that would
If you have limited disk space, you can select Compact installation.
This will install all files except the Help files and the PCL Emulationotherwise be too big for your computer's physical RAM.
If your computer does not have enough physical RAM to run Win-
Front Panel.
dows Printing System efficiently, you can improve performance by
Custom:increasing the amount of virtual memory.
You may also choose Custom installation if you do not want to installNote: If Windows does not allow you to set virtual memory to a
some of the components of the MFP Software. You can go back later
sufficiently large size, it may be that there is not enough
and install the components that you did not install the first timeroom on your hard disk. See your Microsoft Windows User
without having to install the whole of the MFP Software over again.Guide for information on how to fix this and further details on
To do this, start the installation as normal, select Custom, and then
virtual memory.
select the items which you want to install this time, and deselect the
items which have already been installed.For Windows 3.1 and Windows for Workgroups 3.1x:
1. Double-click the Control Panel icon in the Main program group,
5-5. Online Helpand then double-click the 386 Enhanced icon.
In addition to this manual, there are two Online Help files supplied2. In the 386 Enhanced dialog box, click the Virtual Memory button.
with the unit which provide a wealth of information about how to3. In the Virtual Memory dialog box, click the Change button.
operate the MFP Software to its full potential, as well as Windows
4. Enter the desired virtual memory size (we recommend at least 8
Printing System.MB) in the New Size box, and select Permanent in the Type box.
Office WorkTop HelpASelecting Permanent will give the best performance; however,
Office WorkTop Help offers a thorough description of all the featuresthe Temporary setting will give you the maximum available
of Office WorkTop, with step-by-step procedures for faxing, scanning,virtual memory, which may in some cases be greater than that
printing, creating documents, linking to other programs, and more.provided under the Permanent setting. If the memory available
F-3600M Helpis not large enough under Permanent, select Temporary in the
Type box.
The F-3600M Help file is a guide to various functions of the unit, and
also includes troubleshooting tips and techniques. Also included in5. Click the OK button. When the window appears asking you to
this Help file is a section dedicated to the Windows Printing System.confirm your changes, click the Yes button.
Functions of Windows Printing System such as background printing6. To make the changes go into effect, restart Windows.
and default printer settings are covered in full detail to allow you to
For Windows 95:
utilize all of the advanced features.
1. Click the Start button in the task bar.
You can view this Help information by clicking on the Help buttons
which are located in many dialog boxes throughout the software. For2. Select Settings and then click Control Panel in the Settings
help with a particular feature or situation you encounter, rest thegroup.
pointer on the area you would like to find out more about, and press3. In the Control Panel windows, double-click the System icon.
the F1 key.
4. In the System Properties dialog box, click the Performance tab.
Note: You must install the Online Help files to use the Help com-
5. Click the Virtual Memory button under Advanced settings.
mand. If you have note already installed the Online Help
files, refer to "Installation Procedure" above for details on
how to do so.
5 � 7 |
ACEC
