FO-4400U
FO-CS1
Y Soft switch function descriptionSW4 No. 1 ~ No. 3 Communication results printout
It is possible to obtain communication results after each transaction.
SW1 No. 1 ~ No. 4 Recall interval
Choice is made for a recall interval for speed and rapid dial numbers.Normally, the switch is set (No. 1: 0, No. 2: 0, No. 3: 1) so that the
communication result is produced only a communication error is en-
Use a binary number to program this. If set to 0 accidentally, 1 will becountered. If No. 1 was set to 1, No. 2 was set to 1 and No. 3 was set to
assumed.
0, the communication result will be produced every time a communica-
SW1 No. 5 ~ No. 8 Recall timestion is done, even if the communication was successful.
Choice is made as to how many recall times should be made. Use aIf No. 1 was set to 0, No. 2 to 1 and No. 3 to 0, the communication result
binary number to program this.will be produced every transmission.
SW2 No. 1 Dial modeSetting No. 1 to 1 No. 2 to 0 and No. 3 to 0 will disable this function. No
Switch the type according to the telephone circuit connected to the fac-transaction report will be printed.
simile.
If No. 1 was set to 0, No. 2 to 0 and No. 3 to 0, the communication result
0: PULSE DIALis produced only after a timer and memory transmission or when a com-
munication error is encountered.
1: TONE DIAL
SW4 No. 4 Image addition function to the communication result
SW2 No. 2 Receive mode
Auto/manual receiving mode is set.table (for memory transmission only)
Used to set addition of sending image to the communication result table.
SW2 No. 3 ECM mode
SW4 No. 5 Reserved
Used to determine ECM mode function.Set to "0".
SW2 No. 4 ReservedSW4 No. 6 TEL billing code function
Set to "0".
When set to "1", the TEL billing code function is enabled.
SW2 No. 5 Polling securitySW4 No. 7 Billing code position
This switch is employed to enable or disable the polling operation using
When set to "1", the billing code is delivered before dialing the remote
the ID code verification function, in order to prevent unauthorized pollingnumber. When set to "0", the billing code is delivered after dialing.
operation.
SW4 No. 8 Multi-TTI feature
SW2 No. 6 Auto cover sheetWhen this switch is set to "1", Multi TTI function is enabled.
When "1" (=YES) is selected, the cover sheet is automatically sent after
transmission of the original to notify the receiver of the number of origi-SW5 No. 1 Time display format
nal sheets transmitted.When this switch is set to "0", time is displayed in 12-hour system.
When set to "1", 24-hour system.
SW2 No. 7 JUNK-FAX function in manual reception
It is set whether JUNK-FAX is functioned in the manual receiving modeSW5 No. 2 Date display format
or not.Used to select date display/print formats.
SW2 No. 8 JUNK-FAX function0: DAY-Month-Year
This function is used to receive data from a specific remote machine1: Month-DAY-Year
(station registered in entry mode). It is the function that refused a recep-
tion in the case that TSI of remote machine matched with fax number ofSW5 No. 3 Header print
the station registered.When it is set at 0, senderOs name, sending page number and so on are
0: Noautomatically printed in the recording paper on the receiving side during
transmission. Thus, the sender can be known on the receiving side.
1: Yes
0: Applied.
SW3 No. 1 ~ No. 4 Number of rings for auto-receive
1: Not applied.
(0: No ring receive)
When the machine is set in the auto receive mode, the number of ringsSW5 No. 4 Footer print
before answering can be selected. It may be set from one to nine ringsWhen set to "1", the date of reception, the sender machine No., and the
using a binary number. If the soft switch was set to 1, a direct connectionpage No. are automatically recorded at the end of reception.
is made to the facsimile. If it was set to 0 accidentally, receive ring is set
to 1. If it was above 9, receive rings are set to 9.SW5 No. 5 Reserved
Set to "0".
SW3 No. 5 ~ No. 8 Switch to auto-receive from manual receive
SW5 No. 6 Substitute reception
(0: No switch)Selection of substitute reception in the case of recording paper ex-hausted
This setting allows machine to switch from manual to Auto Receive mode.or paper jam. If set to "NO", auto receive is disabled even when the
Setting this number to 0 forces machine to stay in Manual receive mode.receive memory is ready to receive.
Entering the binary number 0 forces the machine to remain in the manual
answer mode. If a number between 1 and 9 is entered, the machine willSubstitute reception is not performed even during receive operation.
go into the answer mode after the given number of rings. HoweverSW5 No. 7 Substitute reception conditions, it can
be used as an ordinary telephone if the handset is taken ofSelection of substitute reception according to existence of f the hookTEL number
before this programmed number is finished. If entry of a number above 9from transmitting side. Initial setting allows substitute reception without
by accident, it will be set to 9. In this case, it must be corrected to theCSI. If set to "no", the receiver cannot receive any documents
proper number.
SW5 No. 8 CSI transmission
CSI signal contains the senderOs phone number registered in the ma-
chine. If this switch is set to "1", no senderOs name will be printed at the
receiving side.
SW6 No. 1 JBIG (Joint Bi-level Image Group)
An image compression encoding method recommended by ITU-T. It re-
alizes 2-second transmission when the power is turned on.
SW6 No. 2 JBIG (Joint Bi-level Image Group) option
An optional function for JBIG.
SW6 No. 3 MMR
MMR (Modified MR) selects presence of the compression function.
2 � 27 |
ACEC
