GQ-100TH
SW-A6 No. 2 End buzzerSW-B4 No. 6 ~ No. 8 Reserved
Setting this bit to 0 will disable the end buzzer (including the errorSet to "0".
buzzer/on-hook buzzer).
SW-B5 No. 1 ~ No. 5 DTMF signal transmission level of lower
SW-A6 No. 3 Disconnect the line when DIS is received in RXfrequency
modeThe transmission level of DTMF signal is adjusted. (lower frequency)
Bit1= 0: When DIS signal is received during RX mode, disconnect the
00000: 0 dBm
line immediately.
Bit1= 1: When DIS signal is received during RX mode, wait the next?
signal.11111: -15.5 dBm (-0.5 dBm x 31)
SW-A6 No. 4 Equalization freeze controlSW-B5 No. 6 ~ No. 8 Reserved
This switch is used to perform reception operation by fixing the equal-Set to "0".
izer control of modem for the line which is always in unfavorable state
and picture cannot be received.SW-B6 No. 1 ~ No. 5 DTMF signal transmission level of higher
frequency
* Usually, the control is executed according to the state of line where
the equalizer setting is changed always.The transmission level of DTMF signal is adjusted. (higher frequency)
SW-A6 No. 5 Equalization freeze 7200 bps only00000: 0 dBm
Setting which specifies SW-A3 No. 6 control only in condition of 7200?
bps modem speed.11111: -15.5 dBm (-0.5 dBm x 31)
SW-A6 No. 6 ~ No. 8 Reserved
SW-B6 No. 6 ~ No. 8 Reserved
Set to "0".Set to "0".
SW-B1 No. 1 ~ No. 4 Recall interval
SW-C1 No. 1, No. 2 Reading slice (binary)
Choice is made for a redial interval for speed and rapid dial calls.
Used a binary number to program this. If set to "0" accidentally, 1 willUsed to determine the set value of reading density in standard/fine
mode. The standard setting is "00" (Factory setting is "00")
be assumed.
SW-C1 No. 3, No. 4 Reading slice (half tone)
SW-B1 No. 5 ~ No. 8 Recall times
Used to determine the set value of reading density in half tone mode.
Choice is made as to how many redials should be.
The standard setting is "00" (Factory setting is "00")
SW-B2 No. 1 Dialing pause
SW-C1 No. 5 Line density selection
Pauses can be inserted between telephone numbers of direct dial
Used to set the transmission mode which is automatically selected
connection. Selection of 4 sec or 2 sec pause is available.when the Resolution key is not pressed. In the copy mode, however,
SW-B2 No. 2 ~ No. 8 Reservedthe fine mode is automatically selected unless the Resolution key is
Set to "0".manually set to another mode.
SW-B3 No. 1 ~ No. 8 ReservedSW-C1 No. 6 ~ No. 8 Reserved
Set to "0".Set to "0".
SW-B4 No. 1 Auto dial mode Delay timer of before line connect.SW-D1 No. 1 ~ No. 4 Number of rings for auto answer mode
Delay time between the dial key input and line connection under theWhen the machine is set in the auto receive mode, the number of
auto dial mode.rings before answering can be selected. It may be set from one to
RAPID01CML RELAY ONfour rings using a binary number. Since the facsimile telephone could
be used as an ordinary telephone if the handset is taken off the hook,
it should be programmed to the user's choice. If the soft switch wasDIALLING
set to "1", direct connection is made to the facsimile.
0 : 0sec
1 : 3secIf a facsimile calling beep was heard when the handset is taken off
the hook, press the START key and put the handset on the hook to
SW-B4 No. 2 Auto dial mode Delay timer of after line connect.have the facsimile start receiving. If it was set to "0" accidentally,
Delay time between the line connection and dial data output underreceive ring is set to "1".
the auto dial mode.NOTE:If the machine is set to answer after a large number of rings, it
DIAL DATAmay not be able to receive faxes successfully.
RAPID01CML RELAY ONIf you have difficulty receiving faxes. reduce the number of
rings to a maximum of 6.
SW-D1 No. 5 Automatic switching from manual to auto receive
0 : 3.0sec
mode
1 : 3.6sec
This soft switch is used to select whether the machine should switch
SW-B4 No. 3 Dial modeto the auto receive mode after 5 rings in the manual receive mode or
remain in the same way as SW-D1 No. 1, No. 2, No. 3 and No. 4
When using the pulse dial, set to "0". When using the tone dial, set to
"0"1"0"1" (5 rings).
"1".
SW-D1 No. 6 ~ No. 8 Reserved
SW-B4 No. 4 key Pulse dial ? Tone dial
Set to "0".
When setting to 1, the mode is changed by pressing thekey from
the pulse dial mode to the tone dial mode.
SW-B4 No. 5 Dial pulse make/break ratio (%)
When using the 33% make ratio pulse dial, set to 0.
When using the 40% make ratio pulse dial, set to 1.
2 � 12 |
ACEC
