AVD-S50/S50ES
2-3. Track/Layer Jump2-5. EEPROM Write Adjust
Track/Layer JumpEEPROM Write Adjust
1. 1TjFWD R.Lj L0>L1
2. 1TjREV L.Lj L1>L0 1. Focus Offset
3.500Tj FineFWD U.Fj L0>L1 2. Focus Gain
4.500Tj FineREV D.Fj L1>L0 3. Trk.Offset Coarse
5.10kTj DircFWD 4. ??????
6.10kTj DircREV 5. Trk.Gain
7.20kTj DircFWD 6. EQBoost
8.20kTj DircREV
0.All Servo Off
0. All Servo Off
Exit: RETURNExit: RETURN
On this screen, track jump, etc. can be performed. Only for the DOn this screen, each item can be adjusted automaticallyVD. Select the
dual layer disc, the focus jump and layer jump are displayed in thedesired number [1] to [10/0] from the remote commander, and
right fieldselected item is adjusted automatically.
[1] 1Tj FWD:1 track jump forward.[1] Focus Offset:Adjusts focus offset.
[2] 1Tj REV:1 track jump reverse.[2] Focus Gain:Adjusts focus gain.
[3] 500Tj FWD:500 track jump (fine search)forward[3]. TRK. OffsetAdjusts tr:acking offset of the RF amp
[4] 500Tj REV:500 track jump (fine search) reverse.(IC001) side.
[5] 10kTj FWD:10k track jump (direct search) forw[5]ar TRK. Gaind.: Adjusts track gain.
[6] 10kTj REV:10k track jump (direct search) reve[6]rse EQ Boost.: Adjusts amount of boost of equalizer.
[7] 20kTj FWD:20k track jump (direct search) forw[10/0]ard.: All servo off.
[8] 20kTj REV:20k track jump (direct search) reverse.
[10/0]:All servo off.2-6. Memory Check
Display images are shown as follows, and all two screens are able
2-4. Non EEPROM Write Adjustto switch by theO key (UP) or o key(D W).
Non EEPROM Write AdjustEEPROM Data 1/2CD SL L0 L1
Focus Gainxx xx xx xx
1. Focus OffsetTrk.Gainxx xx xx xx
2. Focus GainFocus Offsetxx xx xx xx
3. Trk. Offset CoarseTrk.Offsetxx xx xx xx
4. Trk. Offset FineEQ.Boostxx xx xx xx
5. Trk. GainPILevelxx xx -- --
6. EQBoostFcs. Balance-- xx -- --
Jitter xxxx xx xx
0.All Servo OffMirror Timexx xx xx --
FE Level-- xx -- --
Traverse Lv1.-- xx -- --
Exit: RETURNNext:DW Default:CLRExit:RET
On this screen, each item can be adjusted manually. Select the desired
number [1] to [10/0] from the remote commander, and currentEEPROM Data 2/2CDRW DVDRW
setting for the selected item will be displayed, then increase orFocus Gainxxxx
decrease numeric value with theO key or o key. This value isTrk.Gainxxxx
stored in the EEPROM. If CLV has been applied, the jitter isFocus Offsetxxxx
displayed for reference for the adjustment.Trk.Offsetxxxx
EQ.Boostxxxx
[1] Focus Offset:Adjusts focus offset.
[2] Focus Gain:Adjusts focus gain.
[3] TRK. OffsetAdjusts tracking of:fset of the RF amp
(IC001) side.
[4] TRK. Offset:Adjusts tracking offset of the DSP (IC401)
side.
[5] TRK. Gain:Adjusts track gain.Next:UP Default:CLRExit:RET
[6] EQ Boost: Adjusts amount of boost of equalizer.
[10/0]:All servo off.On this screen, current servo adjusted data stored in the EEPROM
are displayed. The adjusted data are initialized by pressing the
[CLEAR] key, but be careful that they are not recoverable after
initialization.
Before clearing the adjusted data, make a note of the set data. This
screen will also a[0]ppear if -All is selected in the Drive Auto
Adjustment. In this case, default setting cannot be made.
19 |
ACEC
