SONY AVD-S500ES Repair Manual

$7.99

SONY AVD-S500ES - It's a complete service manual, and it's in PDF format. It contains circuit diagrams ( schemas ) etc. It also usually contains parts catalog. After placing order we'll send You download instructions on Your email address. See below for delivery information

The manual is available only in language(s): English

Link to manual will be sent on Your email address after You place order.

This product was added to our catalog on Monday 07 May, 2007.

Reviews

Write Review

Buy & Download

Product Reviews

There are currently no reviews for this product.

Other reviews

John Craig - 07/31/2006

Very nice site and the manual is great. A life-saver. Thank you so much!

francesco mayol - 02/11/2007

This is the best site to find what you need.I reccomand all thecnicia n to contact User-Manuals .

Gaspar Lovas - 11/03/2009

That's all right, thank you for all your trouble. Yours sincerely GL

Othmar Herbst - 01/13/2008

PDF contains : - schematics, but a little un-sharp. - disassembly instructions, accurate drawings - description of test-modes

Paul Brady - 01/03/2007

Talk about a lifesaver!!!!!!!!!!!! This schematic will also work for the Radio Shack DX-392. This is the full blown service manual complete with alignment instructions, schematics, and parts lists.

Customers who bought this product also purchased

SONY 7FA-70W Service Manual	SONY 710BK-AL Service Manual	SONY 362B Service Manual
SONY APM-007AV Service Manual	SONY AE-6B CHASSIS Service Manual	SONY 1401 Service Manual

Click to see text excerpt from the manual

AVD-S500ES
SECTION 4
TEST MODE
[Jog Volume Mode]8. Press the > button and the message OLED OFFÃ� is displayed
* Master Volume Check.and all LEDs turn off.
Procedure:9. Press the > button. All segments turn on and all LEDs turn
1. Press the [POWER] button to turn the set on.on just the same as 3.
2. To enter the test mode, press the three bX , [A.F.D] anduttons 10. By pressing the . button and the message OAVD-S500ESÃ�
Z simultaneously.is displayed.
3. The message OJOG 0Ã� is displayed.11.Press the . button and the message ODest <000>Ã� is
4. OJOG 0Ã� value increases like +1, +2, +3 ... if rotating thedisplayed.
[VOLUME] knob clockwise, or it decreases like -1, -2,12.Press the -3, ... if. button and the message OSTR? #,##Ã� is
rotating counter-clockwise.displayed.
5. To exit from this mode, press the [POWER] button to turn the13.Press the . button and the message ODVD? #,##Ã� is
set off.displayed.
14. To exit from this mode[POWER], press the button to turn the
[Key Check Mode]set off.
*Keyboard check.
Procedure:[Disc Tray Lock]
1. Press the [POWER] button to turn the set on.The disc tray lock function for the antitheft of an demonstration
2. To enter the test mode, press three bX ,[PRESET ] uttons Ä�disc in the store is equipped.
and Z simultaneously.Setting Procedure:
3. In the key check mode, the fluorecent indicator displays1. Press the [POWER] button to turn the set on.
OKEYNUM 0Ã�. Each time a button (without the [POWER]2. Press two buttons of x and Z simultaneously for five seconds.
button) is pressed, OKEYNUM 0Ã� value increases. Ho3. The messagwever,e OLOCKEDÃ� is displayed and the tray is locked.
once a button is pressed, it is no longer takReleasing Pren into account.ocedure:
4. To exit from this mode, press the [POWER] button to turn the1. Press two buttons of x and Z simultaneously for five seconds
set off.again.
2. The message OUNLOCKEDÃ� is displayed and the tray is
[Display Test Mode and Version Display Mode]unlocked.
Note:When OLOCKEDÃ� is displayed, the tray lock is not released by turning
* Fluorescent segments and LEDs are tested when this test ispower on/off with the [POWER] button.
activated.
Procedure:
[SHIPMENT Mode]
1. Press the [POWER] button to turn the set on.
2. To enter the test mode, press the thrX ,[DISPLAY] ee buttons *The All Clear clears all data including preset data stored in the
and Z simultaneously.RAM to initial conditions. Execute this mode when returning the
set to the customer.
3. All segments turn on and all LEDs turn on.
( MULTI CHANNEL DECODING LED (blue))Procedure:
1. Press the [POWER] button to turn the set on.
4. Press the > button and confirm the display and all LEDs2. To enter the test mode, press the three b[MODE], uttons
turn on.
5. Press the > button and confirm the display and all LEDs[PRESET+] and Z simultaneously.
3. The LCD displays the message OSHIP MODEÃ�.
turn off.
6. Press the > button and confirm all segments and all LEDs4. Press the G button.
turn off.5. The LCD displays the message OFINISHED!Ã� and the set is
reset.
7. Press the > button and the message OMCD_LED ONÃ� is
displayed and OMULTI CHANNEL DECODINGÃ� LED turn6. To exit from this mode[POWER], press the button to turn the
on.set off.
17