BVM-D32E1WA/D32E1WE/D32E1WU
[C1] Setting the Input Configuration (SET UP 1) N INPUT CONFIGURATION Menu
Notes[C14] SAFE AREA MODE menuNote[C16] COLOR TEMP menu
YEven when selecting AUTO, also select NTSCSet the safe area display modes.The size of the safe area for the 16:9-xx% or 4:3-xx%Select STD, COL1, COL2 or CH SET.
(SETUP 7.5 or 0), PAL (S or D), and PAL-M (S orSIZE: Select the safe area mode.setting depends on the 16:9 button ON/OFF setting.STD: Use common data (factory setting: D65).
D).16:9-80%: Displays a 80% safe area with 16:9COL1: Use common data (factory setting: D93).
YIf there is no input connector or decoderaspect ratio.BVM-D20F1U/D20F1E/D20F1ACOL2: Use common data (factory setting: D65).
corresponding to a format, that format will not be16:9-88%: Displays a 88% safe area with 16:9With 16:9 button ONWith 16:9 button OFFCH SET: Use data for each individual channel.
selectable (the cursor will skip over that entry).aspect ratio.
Chapter 2 Menu16:9-90%: Displays a 90% safe area with 16:9[C17] COPY FROM menuChapter 2 Menu
YIf you change the format of the channel to which the
Select the source to be copied from.
SDI signal is assigned to AUTO of the COMPOSITEaspect ratio.
16:9 80%16:9 80%OTHER CH: Copy data from another channel. Enter
menu with the BKM-21D installed, the image may16:9-93%: Displays a 93% safe area with 16:9
not be displayed. In this case, change the signalaspect ratio.the channel number.
format to NTSC or PAL once, then reset it to AUTO.16:9-ANY SIZE: Displays a safe area with 16:9OTHER MONITOR... : Copy data from a BVM-
DxxE/DxxF series monitor. �[C171]
YIf you change the format of the PAL-M Y/C signal toaspect ratio in the size determined by H SIZE
MEMORY CARD... : Copy data from a memory
AUTO of the YC menu with the BKM-26M installed,and V SIZE.
card. �[C172]
the image may not be displayed. In this case, select4:3-80%: Displays a 80% safe area with 4:34:3 80%4:3 80%
PAL-M S or D.aspect ratio.
4:3-88%: Displays a 88% safe area with 4:3[C171] OTHER MONITOR menu
Enter the address number of the source monitor.
[C112] COMPONENT menuaspect ratio.
MONITOR ADDRESS: Enter the address number of
Select the component signal format, or RGB.4:3-90%: Displays a 90% safe area with 4:3BVM-D24E1WU/D24E1WE/D24E1WA/
the monitor from which to copy data. �[C1711]
YPBPR SMPTE/EBU-N10aspect ratio.D32E1WU/D32E1WE/D32E1WA
YPBPR BETACAM: SETUP 7.5 or 0.4:3-ANY SIZE: Displays a safe area with 4:3With 16:9 button ONWith 16:9 button OFF[C1711] MONITOR ADDRESS menu
RGBaspect ratio in the size determined by H SIZE
Assign the channel of the selected monitor from which
and V SIZE.
to copy data. � Copy is carried out.
[C113] SDI menuH SIZE: When 16:9-ANY SIZE or 4:3-ANY SIZE is
16:9 80%16:9 80%
Select the format of the serial digital signal 1).selected, adjust the horizontal size of the safe areaCH NO: Enter the channel number.
NTSC: SETUP 7.5 or 0.in 1% steps.[C172] MEMORY CARD menu
PAL: S (simple) or D (delay)V SIZE: When16:9-ANY SIZE or 4:3-ANY SIZE is
Select the file name.
4:2:2selected, adjust the vertical size of the safe area in
FILE NAME: Select the file name. �[C1721]
AUTO: The NTSC, PAL or 4:2:2 format of the input1% steps.
signal is detected and switched automatically. 1)H POSITION: Adjust the horizontal display position4:3 80%4:3 80%Note
of the safe area (�32 to +32).
1) Y It will take a few seconds to detect the format of anThe input signal is not displayed during the data
SHAPE: Select the shape of the SAFE AREA
input signal when AUTO is selected. It isloading.
MARKER.
recommended that a particular format be selected if it
is determined.SHAPE A: [C1721] FILE NAME menu
Y If the serial digital signal is not properly displayed in[C15] CHANNEL NAME menuAssign the channel of the selected file from which to
SDI AUTO mode, re-enter the channel number.Give the channel a name. Select a preset name, orcopy data. � Copy is carried out.
enter a new one.CH NO: Enter the channel number.
HD SDIPROG: Program signal
EDIT: Signal from an editor
[C12] YC SEP menuSHAPE B: CAM: Camera signal
Select a Y/C separation filter.VTR: Signal from a VTR
TRAP/BPF: Select TRAP/BPF filter.NEW NAME: Enter a new name. (Up to 20
2 LINES COMB: Select 2 LINES COMB filter.characters can be entered and up to six characters
3 LINES COMB: Select 3 LINES COMB filter.from the head of the name are displayed in the
4:3 AREA MARKER: Select whether the 4:3 line isINPUT CONFIGURATION menu ([C1] 2/2).)
[C13] SCREEN MODE menudisplayed in16:9 screen or not (ON or OFF).
Select the scan size.4:3 BLANKING: Select the blanking outside the 4:3
16:9-NORM: Overscanned 16:9 aspect ratio.area.
16:9-UNDR: Underscanned 16:9 aspect ratio.HALF: Half blanking
4:3-NORM: Overscanned 4:3 aspect ratio.BLACK: Blanks outside the 4:3 area.
4:3-UNDR: Underscanned 4:3 aspect ratio.OFF: Do not blank.
3839
1-23 |
ACEC
