1-22
E Setting the Power-Up Conditions and Data about
D Assigning the Remote Control Functions N REMOTE Menu
the Screen Display N SYSTEM CONFIG Menu
Setting Lists of the REMOTE MenuOverview
This section explains the setting lists displayed in theNoteThe SYSTEM CONFIG menu is displayed on the twomonitor.
menu.PINs 1 to 4, and PIN 6 of the PARALLEL REMOTEpages.
1 and 2 are connected inside the unit, thereforeThe SYSTEM CONFIG (1/2) menu is used for theThe SYSTEM CONFIG (2/2) menu is used for the
How to read the setting listsdifferent functions cannot be assigned to those pins.following settings:following settings:
Chapter 2 MenuYFor purposes of explanation, each setting list isChapter 2 Menu
preceded by a menu number. These numbers are not[D211] (1/2) 1-8 PIN menu (1/2)YPower-up condition (STANDBY MODE menu)YDisplay mode and position of the signal format
displayed on the screen.Assign a function to the selected pin.This menu sets the condition of the monitor when the(FORMAT DISPLAY and POSITION menus)
For more information about the menu number, see OAboutMAIN POWER switch on the rear panel is switchedYDisplay mode and position of the channel number
CH: Select a channel number. Enter the desired
menu numbers� on page 26(E).on (BVM-D14H1U/D14H1E/D14H1A/D14H5U/(CH NO and POSITION menus)
channel number with the numeric keypad.
YThe arrow mark (�) refers you to another setting listD14H5E/D14H5A) or when the battery is installedYDisplay mode and position of the channel name
----: Set to unused.
that appears after you make the setting, or to an(BVM-D9H1U/D9H1E/D9H1A/D9H5U/D9H5E/(CH NAME and POSITION menus)
UNDER SCAN: Set underscan on or off.
operation that is carried out as a result of the setting.D9H5A.)
16:9: Set a 16:9 aspect ratio on or off.YDisplay mode of the caption (CAPTION menu)
When there is no arrow mark, the menu does not haveYPower-up input channel (DEFAULT CH menu)
H DELAY: Set the horizontal sync display on or off.
any sub-list.This menu sets the power-up input channel.YMaintenance (MAINTENANCE menu)
V DELAY: Set the vertical sync display on or off.
EXT SYNC: Set the synchronization to external syncYTime from power-up until degauss (DEGAUSSThis is for a service qualified personnel.
[D] REMOTE menuDELAY menu)
signals enabled or disabled.
Select the type of remote control.
APERTURE: Set the correction of frequencyIf several monitors are turned on at the same time and
SERIAL REMOTE : Set the address and groupall start degaussing at the same time, there will be a
characteristics enabled or disabled.
number of the monitor controlled via the SERIALvery large current draw on the power supply for a few
MONO: Set monochrome display on or off.
REMOTE connector. �[D1]moments. To prevent this, the delay time between
BLUE ONLY: Set the blue signal pictures display
PARALLEL REMOTE: Select whether parallelpower-up and degaussing can be set for each monitor
(monochrome) on or off.
remote control will be used or not (ON or OFF.)
independently.
PARALLEL REMOTE CONFIG : Set the pin
[D211] (2/2) 1-8 PIN menu (2/2)YSetting of the contrast and brightness after
assignments for the PARALLEL REMOTEadjusting the white balance (CONT/BRT HOLD
Assign a function to the selected pin.
connector. �[D2]menu)
R OFF: Set cutting red beams enabled or disabled.
G OFF: Set cutting green beams enabled or disabled.Selects if the adjusted contrast and brightness are
[D1] SERIAL REMOTE menu
B OFF: Set cutting blue beams enabled or disabled.retained or they are reset to the center values, when
Set the monitor address and group number.
4:3 MARKER: Set the 4:3 marker display on or off.the color temperature is adjusted in the COLOR
MONITOR ADDRESS: Enter a number.
CAPTION VISION: Set Caption Vision on or off.TEMP ADJ menu.
GROUP ADDRESS: Enter a number.
TALLY RED: Set tally red on or off.YAssigning shortcut to the COLOR TEMP ADJ
TALLY GREEN: Set tally green on or off.menu to the [F2] key (COL TEMP SHORT-CUT
[D2] PARALLEL REMOTE CONFIG menumenu)
DEGAUSS: Set degaussing on or off.
Select the PARALLEL REMOTE connector pins for
POWER OFF: Set the monitor power on or off.Assigns the shortcut to the MANUAL menu of the
which you want to change the function. The factory
COLOR TEMP ADJ menu to the [F2] key. This
settings for each pin are given below. �[D211]
For the pin assignment, see OPARALLEL REMOTE 1/2allows you to jump directly to the MANUAL menu
PINs 1 to 4, and PIN 6 of the PARALLEL REMOTEconnectors� in the Location and Function of Parts on pagecorresponding to the color temperature set to the
BVM-D9H1U/D9H5U/D9H1E/D9H5E/D9H1A/D9H5A1 and 2 are common settings.13(E) for BVM-D9H1U/D9H1E/D9H1A/D9H5U/D9H5E/currently displayed image (STD/COL 1/COL 2.)
1 PIN: CH01D9H5A or page 22(E) for BVM-D14H1U/D14H1E/YAuto color control (ACC SW menu) (when using
2 PIN: CH02D14H1A/D14H5U/D14H5E/D14H5A.
the BKM-127W)
3 PIN: TALLY RED
Selects if the ACC (Auto Color Control) circuit is
4 PIN: TALLY GREEN
turned on or off.
5 PIN: EXT SYNC (PARALLEL REMOTE [1])YSelecting the monitor to copy the original data
GND (PARALLEL REMOTE [2])
(CONFIG COPY menu)
6 PIN: UNDERSCAN
Setting data of the INPUT CONFIG and SYSTEM
7 PIN: 16:9CONFIG (except the DEGAUSS DELAY data)
8 PIN: 4:3 MARKERmenus can be copied from the serial connected
38 (E)39 (E) |
ACEC
