Special Aging Mode FunctionsAging Procedure
The aging mode is provided with the following con1.vTenient func-urn ON the power of the unit. Pr¤ OPEN/CLOSE andess the
tionsopen the front cover.
Y Disc setting mode (*1)2. Change the COMMAND MODE switch (S901) on set to CD1 .
Y Selection of presence of protection function during error (*2)3. Press the AGING START button of the remote commander for
Y Count function of aging cycle (*3)aging mode (J-2501-123-A).
4. When the disc set mode is set, the á and P LEDs blink.
*1 Disc setting mode:5. Rotate the DISC/CHARACTER dial. The slits (No. 60, 120,
5 discs are set before setting the aging mode. This mode mak180, 240, 300) fes or setting the discs will come forward. Insert the
the setting of these discs more easy.discs into these slits. Do not set the discs in other slits.
*2 Self protection function during errors:6. Set whether the self-protection function during errors is equipped
Function which voluntarily corrects errors which occur duringwith the unit. Press the REPEAT button. If OREPEAT� is dis-
normal operations by retries.played on the Fluorescent indicator tube, it means the function
If this function is not provided, all operations will be stoppedis provided. If OREPEAT� is not displayed, it means the function
without retiring. It is suitable for checking erroris not pros with lovided.w re-
producibility.
If this function is provided, and errors can be corError Displarected byy re-
Disc number
tries, aging will be continued without stopping.
when aging
*3 Aging cycle count function:a ç e
Functions which displays the number of agings carried out on
180
the Fluorescent indicator tube in numbers. One aging cycle con-
sists of five discs.12 0E 0 1#
number of disc tablea ç ea ç ea ç e
Disc numberError codeAging cycle
1DISCwith errornumber
CD1120
DISC
7. Press the á button.
AGED 10
8. The á LED blinks, the aging mode is set, and aging is started.
9. The aging cycle lasts 3 minutes. If errors occur during aging, the
error number will be displayed on the Fluorescent indicator tube.number of agings
(Refer to the following table for the details of the errors.)
10. Aging will be repeated as long as no errors occur.
11. After each aging cycle, the number displayed on the Fluorescent
indicator tube will increase.
12. To end aging, disconnect the power cord from the outlet.
NOTE: As an alternative to steps 2 and 3, press the GROUP 1
button, ¤OPEN/CLOSE button, and +100 button at the
same time.
Error code
Code numberNameContents
Err 01DISC sensor check 1No disc in the specified slit
Err 02DISC sensor check 2Disc in other slits
Err 03Table operation check 1Table motor current over
Err 04Table operation check 2No table sensor input
Err 05Loading operation check 1 Load in timeover
Err 06Loading operation check 2 Load out timeover
Err *1BU related check 1Access timeover
Err *2BU related check 2High speed search NG
Err *3BU related check 3Q data read error
Err *4BU related check 4BU operation (from focus search to until signal can be read) timeover
Err *5BU related check 5GFS monitor error
Err *6BU related check 6Focus cannot be imposed by focus search
Err *7BU related check 7Auto focus bias adjustment cannot be performed
The * numbers mean the following according to the state of the unit during aging
2 : From chucking to end of TOC read
3 : From end of TOC read to end of last track playback
4 : From end of last track playback to end of first track playback
� 11 � |
ACEC
