p CPD-120AS
Computer
Getting Started to USB port
Before using this display, please make sure that the following items are included
in your package:Blue (to display
Y Multimedia computer display (1)connector)
Y Warranty card (1)Green (to speaker
Y Operating instruction manual (1)connector)
Y Windows 95 Monitor Information Disk and its instruction manual (1)
Red (to microphone
connector)
. Tip
This display will sync with any IBM or compatible system equipped with VGA1) or greater graphics
capability. Although this display will sync to other platforms running at horizontal frequencies
between 30 and 70 kHz, including Macintosh2) and Power Macintosh systems, a cable adapter is to
required. Please consult Sony Technical Support for advice on which adapter is suitable for your
needs.
p CPD-220AS
1)VGA is a trademark of IBM Corporation.Computer
2)Macintosh is a trademark of Apple Computer Inc. to USB port
InstallationBlue (to display
connector)
p Step 1: Connect the computerGreen (to speaker
With the computer switched off, connect the video signal cable to the displayconnector)
(VGA) connector on your computer. If your computer supports the DDC plug-Red (to microphone
and-play standard, this connection will enable the DDC communication betweenconnector)
the display and the computer.
Also the video signal cable is combined with audio and microphone cables. If
your computer is equipped with sound capability, connect the audio and to
microphone plugs to appropriate jacks located on your computer.
If you use a USB (universal serial bus) device, connect the USB device to the
USB downstream jack and the PC to the USB upstream jack.4Note on handling the video signal cable
Do not touch the pins of the video signal cable.
4Note on USB ports
USB ports are included to provide state-of-the-art technology. Until USB support is
available at the operating system level, you must supply drivers to use USB devices.
You can upgrade your operating system to a version that supports USB at the
operating system level once a version becomes available.
See the manual that came with your USB device for more information on setting it up
and using it.
Continued to the ne�xt page
Getting Started11GB
10GBGetting Started
Using Your Display
p Step 2: Connect the power cord
With the display switched off, connect the power cord to the display and thePreset and user modes
other end to a power outlet.
The Multiscan CPD-120AS/220AS display has factory preset modes for the 10
most popular industry standards for true Oplug and play� capability.
p CPD-120ASFor less common modes, its Digital Multiscan Technology will perform all of
the complex adjustments necessary to ensure a high quality picture for any
timing between 30 and 70kHz.
to a power outlet
Power cord (supplied)NO.ResolutionHorizontalVertical
(dots ´ lines)FrequencyFrequency
1640 ´ 40031.5 kHz70 Hz
2640 ´ 48031.5 kHz60 Hz
p CPD-220AS3640 ´ 48043.3 kHz85 Hz
4800 ´ 60037.9 kHz60 Hz
5800 ´ 60046.9 kHz75 Hz
to a power outlet61024 ´ 76860.0 kHz75 Hz
71024 ´ 76868.7 kHz85 Hz
Power cord (supplied)81152 ´ 86444.8 kHz47 Hz (95 Hz interlace)
91152 ´ 86454.8 kHz60 Hz
101280 ´ 102464.0 kHz60 Hz
p Step 3: Turn on the display and computer.4Note for Windows¨ 95 users
Install the new model information of the Sony computer display from OWindows 95 Monitor
p Step 4: If necessary...Information disk� into your PC. (To install the file, refer to the attached OAbout the Windows 95
Adjust the user controls according to your personal preference.Monitor Infomration Disk�.)
The installation of your display is complete. Enjoy your display.This display complies with OVESA DDC,� the standards of Plug & Play. If your PC/graphic board
complies with DDC, select OPlug & Play Display (VESA DDC)� or this displayOs model name (CPD-
120AS/220AS) as ODisplay type� from OControl Panel� on Windows 95. Some PC/graphic boards
do not comply with DDC. Even if they comply with DDC, that may have some problems on
connecting this display. In this case, select this displayOs model name (CPD-120AS/220AS) as
ODisplay type� on Windows 95.
Windows¨ is a registered trademark of Microsoft Corporation in the United States and other
countries.
4Note on recommended horizontal timing conditions
Horizontal sync width should be more than 1.0 ?sec.
Horizontal blanking width should be more than 3.6 ?sec.
Continued to the ne�xt page
12GBGetting StartedUsing Your Display13GB
� 6 � |
ACEC
