CPD-2003GT
Customizing Your MonitorTechnical FeaturesAdditional Information
Video Enhancement ModeSpecificationsWarning Messages
You can automatically change the characteristics of the pictureIf there is something wrong with the input signal, one of the following messages appears.
Picture tube0.25 mm aperture grill pitch,
to match the way you use your monitor with the Video
17 inches measured diagonally,
Enhancement Mode. Simply press this button to cycle90 degree deflectionThe input signal condition
through the three modes.INFORMATION
Viewable image sizeApprox. 327 ´ 243 mm (w/h)OOUT OF SCAN RANGE� indicates that the input signal
(12 7/8 ´ 9 5/8 in.)is not supported by the monitorOs specifications.
1Turn on the monitor and computer.
16.0� viewing imageInput signal conditionOUT OF SCAN RANGE
ONO INPUT SIGNAL� indicates that no signal is input.
Resolution
2Press this button to set the mode.The message disappears after about 30 seconds.
HorizontalMax. 1280 dots
VerticalMax. 1024 lines
To solve these problems, see the OTroubleshooting� section
Display picture sizeApprox. 312 ´ 234 mm (w/h)below.
(12 3/8 ´ 9 1/4 in.)
Deflection frequency
Horizontal30to 85 kHzTroubleshooting
Each time you press the Video Enhancement Mode button,Vertical50 to 120 HzThis section may help you isolate the cause of a problem and as a result, eliminate the need to contact technical support.
the mode changes and appears on the screen as follows.AC input voltage/current
100 to 120 V, 50/60 Hz, 1.8 A
n STANDARD MODEnn220 to 240 V, 50/60 Hz, 1 ASymptomCheck these items
No picture
Dimensions406 ´ 432 ´ 420 mm (w/h/d)
PRESENTATION MODE
(16 ´ 17 1/8 ´ 16 5/8 in.)If the u indicator is not litY Make sure the power cord is properly connected.
GRAPHICS/VIDEO MODEMassApprox. 18 kg (39 lb 11 oz)Y Make sure the u (POWER) switch is in the OON� position.
Design and specifications are subject to change without notice.If the ONO INPUT SIGNAL�Y Try pressing any key on the computer keyboard.
message appears on the screen, orY Make sure your computer is turned on.
The STANDARD MODE is ideal for spreadsheets, wordif the u indicator is either orangeY Make sure the video signal cable is properly connected and all plugs are firmly seated in
N 8 Nprocessing, and other text oriented applications.
or alternating between green andtheir sockets.
orangeY Make sure none of the HD15 video input connector pins are bent or pushed in.
The PRESENTATION MODE is useful for presentationY Make sure the video board is completely seated in the proper bus slot.
programs that require vivid colors.Monitor Information
If the OOUT OF SCAN RANGE�Y Make sure the video frequency range is within that specified for the monitor.
The GRAPHICS/VIDEO MODE gives movies and gamesYou can display the model name, serial number and year ofmessage appears on the screenHorizontal: 30 � 85 kHz
enhanced visual appeal by increasing the sharpness andmanufacture using the INFORMATION OSD.Vertical: 50 � 120 Hz
brightness.Refer to your computer systemOs instruction manual to adjust the video frequency range.
Press and hold the MENU button for 5 seconds.Y If you are using a video signal cable adapter, make sure it is the correct type.
The selected mode indication appears on the screen for aboutThe INFORMATION OSD appears.
three seconds.If no message is displayed andY Run the SELF TEST function:
INFORMATIONthe u indicator is green or1. Turn off the monitor and disconnect the video cable from the computer.
If the screen appears too white, adjust the color temperatureMODEL : CPD-2003GTflashing orange2. Turn on the monitor and wait five seconds. The ONO INPUT SIGNAL� message
(see OUsing the COLOR OSD� on page 7).SER NO : 1234567: 1998should appear with a color bar pattern. The message and pattern are
MANUFACTURED displayed for 30 seconds.
If the monitor displays White, Red, Green and Blue colors, the monitor is
The INFORMATION OSD includes the model name, serialfunctioning properly.
NoteY Make sure none of the HD15 video input connector pins are bent or pushed in.
number and year of manufacture.
The PRESENTATION MODE and GRAPHICS/VIDEO MODE may
produce ghost images when displaying text oriented applications.The OSD automatically disappears after about 30 seconds.Picture is scrambledY Check your video board manual for the proper monitor setting.Y Check this manual and make sure the monitor supports the graphics mode and the
These modes change the brightness of the picture dynamically
according to changes in moving pictures. If ghost images appear,frequency at which you are trying to operate. Even if the frequency is within the proper
set the Video Enhancement Mode to STANDARD MODE.range, some video boards may have a sync pulse that is too narrow for the monitor to
sync correctly.
Color is not uniformY Degauss the monitor (page 8).
If you place equipment which generates a magnetic field, such as a loudspeaker, near the
monitor, or you change the direction of the monitor, the color may not be uniform.
The degauss function demagnetizes the metal frame of the CRT to obtain a neutral field
for uniform color reproduction. If a second degauss cycle is needed, allow a minimum
interval of 20 minutes for the best result.
1012 |
ACEC
