7USC:\WIN95-E\DESKTOP\CPD E100\386765901CPDE100UC\386765901CPDE100UC\01US03BAS-masterpage:Right
UC.fm
01US01COV-UC.book Page 7 Thursday, July 1, 1999 5:01 PM
Step 3: Turn on the monitor and Selecting the on-screen menu
computerlanguage (LANGUAGE/
INFORMATION)
First turn on the monitor, then turn on the computer.
English, French, German, Italian, Spanish, Russian and Japanese
versions of the on-screen menus are available. The default setting
is English.
1Press the center of the control button.
The installation of your monitor is complete.
See page 9 for more information on using the control button.
If necessary, use the monitor?s controls to adjust the picture.
MENU
If no picture appears on your screenMENU
EX I T
H- S I ZE / CENTER
? Check that the monitor is correctly connected to the computer.V-S I ZE / CENTER
? If NO INPUT SIGNAL appears on the screen, confirm that PI N /PI N BALANCE
KEY / KEY BALANCE
your computer?s graphic board is completely seated in the ROTAT ION
ZOOM
correct bus slot. COLOR
LANGUAGE / I NFORMAT INO
? If you are replacing an old monitor with this model and OUT
DEGAUSS / CANCEL MOIER
OF SCAN RANGE appears on the screen, reconnect the old SELECT
monitor. Then adjust the computer?s graphic board so that the
horizontal frequency is between 30 - 70 kHz, an2d tMoheve th verte cicalontrol buttonm/M to highlight
frequency is between 48 - 120 Hz.LANGUAGE/INFORMATION and press the center of
the control button again.
For more information about the on-screen messages, see ?Trouble
MENU
symptoms and remedies? on page 14.LANGUAGE/ INFORMATION
US
ENGL I SHFRAN?A I S
DEUTSCHI TAL I ANO
For customers using Windows 95/98ESPA?OL
To maximize the potential of your monitor, install the new model
information file from the supplied Windows Monitor Information Disk SELECTEX I T
onto your PC.
This monitor complies with the ?VESA DDC? Plug & Play standard. If
your PC/graphics board complies with DDC, select ?Plug & Play Monitor
(VESA DDC)? or this monitor?s model name as the monitor t3 ypeMove th in the ce ontrol buttonm/M to select
?Control Panel? of Windows 95/98. If your PC/graphics board(LA hNas GUAGE) and move </, to select a language.
difficulty communicating with this monitor, load the Windows Mo?ENGLISnitor H
Information Disk and select this monitor?s model name as the monitor ? FRAN�AIS: French
type.
? DEUTSCH: German
? ITALIANO: Italian
? ESPANOL: Spanish
For customers using Windows NT4.0
?: Russian
Monitor setup in Windows NT4.0 is different from Windows 95/98 and
does not involve the selection of monitor type. Refer to th?e Window: Jas panese
NT4.0 instruction manual for further details on adjusting the resolution,
refresh rate, and number of colors.To close the menu
Press the center of the control button once to return to the main MENU,
and press again selecting EXIT to return to normal viewing. If no buttons
Adjusting the monitor?s resolution and color numberare pressed, the menu closes automatically after about 30 seconds.
Adjust the monitor?s resolution and color number by referring to your
computer?s instruction manual. The color number may varyTo reset accordito Eng tnog lish
your computer or video board. The color palette setting anPress td thehe ac RESETtual bu tton while the (LANGUAGE) menu is displayed
number of colors are as follows:on the screen.
? High Color (16 bit 65t) ,536 colors
? True Color (24t b abitout) 16.77 million colors
In true color mode (24 bit), speed may be slower.
7
CPD-E100
3-867-659-01 (1) |
ACEC
