The operating instructions mentioned here are partial abstracts
SECTION 1from the Operating Instruction Manual. The page numbers of
the Operating Instruction Manual remein as in the manual.
GENERAL
Use of the tilt-swivel
PrecautionsIdentifying parts and controls
This monitor can be adjusted within the angles shown below. To
find the center of the monitorOs turning radius, align the center of
Warning on power connectionsthe monitorOs screen with the centering dots on the stand.See the pages in parentheses for further details.
Y Use the supplied power cord. If you use a different power cord, Hold the monitor at the bottom with both hands when you turn it FrontRear
be sure that it is compatible with your local power supply.horizontally or vertically. Be careful not to pinch your fingers at
For the customers in the U.S.A.the back of the monitor when you tilt the monitor up vertically.
If you do not use the appropriate cord, this monitor will not
conform to mandatory FCC standards.MENU
RESET
Example of plug types
90u
15uAC IN
MENU
90uRESET
5u
for 100 to 120 V ACfor 200 to 240 V AC
Y Before disconnecting the power cord, wait at least 30 seconds
after turning off the power to allow the static electricity on the
screenOs surface to discharge.Centering dots
Y After the power is turned on, the screen is demagnetized
(degaussed) for about 5 seconds. This generates a strong
magnetic field around the screen which may affect data stored 1 RESET button (page 12)4 AC IN connector (page 6)
on magnetic tapes and disks placed near the monitor. Be sure to This button resets the adjustments to the factory settings.This connector provides AC power to the monitor.
keep magnetic recording equipment, tapes, and disks away
from the monitor.2 Control button (page 9)5 Video input connector (HD15) (page 6)
The control button is used to display the menu and make This connector inputs RGB video signals (0.700 Vp-p,
1-1The equipment should be installed near an easily accessible adjustments to the monitor, including brightness and contrast positive) and sync signals.US
outlet.adjustments.
1 2 3 4 5
Installation3 1 (power) switch and indicator (pages 7, 13, 16)6 7 89 10
Do not install the monitor in the following places:This button turns the monitor on and off. The power indicator 11 12 13 14 15
Y on surfaces (rugs, blankets, etc.) or near materials (curtains, lights up in green when the monitor is turned on, and either
draperies, etc.) that may block the ventilation holesflashes in green and orange, or lights up in orange when the
Y near heat sources such as radiators or air ducts, or in a place monitor is in power saving mode.Pin No.Signal
subject to direct sunlight1Red
Y in a place subject to severe temperature changes
Y in a place subject to mechanical vibration or shock2Green
Y on an unstable surface(Sync on Green)
Y near equipment which generates magnetism, such as a 3Blue
transformer or high voltage power lines
4ID (Ground)
Y near or on an electrically charged metal surface
5DDC Ground*
Maintenance6Red Ground
Y Clean the screen with a soft cloth. If you use a glass cleaning
7Green Ground
liquid, do not use any type of cleaner containing an anti-static
solution or similar additive as this may scratch the screenOs 8Blue Ground
coating.9�
Y Do not rub, touch, or tap the surface of the screen with sharp or
10Ground
abrasive items such as a ballpoint pen or screwdriver. This type
of contact may result in a scratched picture tube.11ID (Ground)
Y Clean the cabinet, panel and controls with a soft cloth lightly 12Bi-Directional Data (SDA)*
moistened with a mild detergent solution. Do not use any type
of abrasive pad, scouring powder or solvent, such as alcohol or 13H. Sync
benzene.14V. Sync
15Data Clock (SCL)*
Transportation
When you transport this monitor for repair or shipment, use the * DDC (Display Data Channel) is a standard of VESA.
original carton and packing materials.
45 |
ACEC
