The following are partial abstracts from the Operating InstructionSECTION 1
Manual. The page numbers shown reflect those of the Operating
GENERAL
Instruction Manual.
Identifying parts and controls
Use of the tilt-swivelSee the pages in parentheses for further details.
Precautions
This monitor can be adjusted within the angles shown beloFrw.ont To Rear
find the center of the monitor?s turning radius, align the center of
Warning on power connectionsthe monitor?s screen with the centering dots on the stand.
? Use the supplied power cord. If you use a differeHoldnt p thowee mr oconitord, r at the bottom with both hands when you turn it
be sure that it is compatible with your local phoowerizor suntppallyly. or vertically. Be careful not to pinch your fingers at MENU
For the customers in the U.S.A.the back of the monitor when you tilt the monitor up vertically.RESETAC IN
If you do not use the appropriate cord, this monitor will not
conform to mandatory FCC standards.
Example of plug typesMENU
90°RESET
15°
90°
5°
for 100 to 120 V ACfor 200 to 240 V AC
? Before disconnecting the power cord, wait at least 30 seconds
after turning off the power to allow the static electricity on the
screen?s surface to discharge.Centering dots
? After the power is turned on, the screen is demagnetized 1 RESET button (page 12)4 AC IN connector (page 6)
(degaussed) for about 5 seconds. This generates a strong This button resets the adjustments to the factory Thsiestt coingnns.ector provides AC power to the monitor.
magnetic field around the screen which may affect data stored
on magnetic tapes and disks placed near the monitor. Be sure to 2 Control button (page 9)5 Video input connector (HD15) (page 6)
keep magnetic recording equipment, tapes, and disks away The control button is used to display the menu anTd mhisa keco nnector inputs RGB video signals (0.700 Vp-p,
from the monitor.adjustments to the monitor, including brightness aponsitivd conte)ra ast nd sync signals.US
? 5 ?
adjustments.
The equipment should be installed near an easily accessible 1 2 3 4 5
outlet.3 1 (power) switch and indicator (pages 7, 13, 16)6 7 89 10
This button turns the monitor on and off. The power indicator 11 12 13 14 15
Installationlights up in green when the monitor is turned on, and either
Do not install the monitor in the following places:flashes in green and orange, or lights up in orange when the
? on surfaces (rugs, blankets, etc.) or near materials (curtains, monitor is in power saving mode.Pin No.Signal
draperies, etc.) that may block the ventilation holes
? near heat sources such as radiators or air ducts, or in a place 1Red
subject to direct sunlight2Green
? in a place subject to severe temperature changes(Sync on Green)
? in a place subject to mechanical vibration or shock
? on an unstable surface3Blue
? near equipment which generates magnetism, such as a 4ID (Ground)
transformer or high voltage power lines5DDC Ground*
? near or on an electrically charged metal surface
6Red Ground
Maintenance7Green Ground
? Clean the screen with a soft cloth. If you use a glass cleaning
8Blue Ground
liquid, do not use any type of cleaner containing an anti-static
solution or similar additive as this may scratch the screen?s 9-
coating.
10Ground
? Do not rub, touch, or tap the surface of the screen with sharp or
abrasive items such as a ballpoint pen or screwdriver. This type 11ID (Ground)
of contact may result in a scratched picture tube.12Bi-Directional Data (SDA)*
? Clean the cabinet, panel and controls with a soft cloth lightly
moistened with a mild detergent solution. Do not use any type 13H. Sync
of abrasive pad, scouring powder or solvent, such as alcohol or 14V. Sync
benzene.
15Data Clock (SCL)*
Transportation* DDC (Display Data Channel) is a standard of VESA.
When you transport this monitor for repair or shipment, use the
original carton and packing materials.
CPD-E210
5
4 |
ACEC
