D-NE710/NE711/NE715/NE718CK
TABLE OF CONTENTSThis appliance is classified as a CLASS 1 LASER product.
The CLASS 1 LASER PRODUCT MARKING is located on
the rear exterior.
1. SERVICING NOTEáááááááááááááááááááááááááááááááááááááááááááááááááááááááááá3
2. GENERALáááááááááááááááááááááááááááááááááááááááááááááááááááááááááááááááááááááááááá4
3. DISASSEMBLYáááááááááááááááááááááááááááááááááááááááááááááááááááááááááááááááá5
4. ELECTRICAL CHECKINGááááááááááááááááááááááááááááááááááááááááááá8
CAUTION
5. DIAGRAMSáááááááááááááááááááááááááááááááááááááááááááááááááááááááááááááááááááááááá9
Use of controls or adjustments or performance of procedures
5-1. Block Diagram � MAIN Section (1/2) � ááááááááááááááááááááá 10
other than those specified herein may result in hazardous
� MAIN Section (2/2) �ááááááááááááááááááááááááááááááááááááááááááááááá 11
radiation exposure.
� Power Supply Section � ááááááááááááááááááááááááááááááááááááááááááá 12
5-2. Printed Wiring Board � MAIN Board (Side A) � ááááááá 13
5-3. Printed Wiring Board � MAIN Board (Side B) �ááááááá 14Flexible Circuit Board Repairing
5-4. Schematic Diagram � MAIN Board (1/4) � ááááááááááááááá 15YKeep the temperature of the soldering iron around 270 uC dur-
5-5. Schematic Diagram � MAIN Board (2/4) � ááááááááááááááá 16ing repairing.
5-6. Schematic Diagram � MAIN Board (3/4) � ááááááááááááááá 17Y Do not touch the soldering iron on the same conductor of the
5-7. Schematic Diagram � MAIN Board (4/4) � ááááááááááááááá 18circuit board (within 3 times).
5-8. IC Block Diagrams áááááááááááááááááááááááááááááááááááááááááááááááááááááá 19Y Be careful not to apply force on the conductor when soldering
5-9. IC Pin Function Descriptions áááááááááááááááááááááááááááááááááááááá 22or unsoldering.
Notes on chip component replacement
6. EXPLODED VIEWSáááááááááááááááááááááááááááááááááááááááááááááááááááááá27
YNever reuse a disconnected chip component.
Y Notice that the minus side of a tantalum capacitor may be dam-
7. ELECTRICAL PARTS LISTááááááááááááááááááááááááááááááááááááááá30
aged by heat.
Unleaded solder
Notes on the power source
Boards requiring use of unleaded solder are printed with the lead-
Disconnect all power sources when the CD player is not used for a long time.
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
On AC power adaptor
the lead free mark due to their particular size.)
Y Use only the AC power adaptor supplied.
If your CD player is not supplied with the one, use the AC-E45HG AC
power adaptor. Do not use any other AC power adaptor. It may cause a
: LEAD FREE MARKmalfunction.
Unleaded solder has the following characteristics.
Y Unleaded solder melts at a temperature about 40!C higher thanPolarity of the plug
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350!C.
Y Do not touch the AC power adaptor with wet hands.
Caution: The printed pattern (copper foil) may peel away if the
Y Connect the AC power adaptor to an easily accessible AC outlet. Should
heated tip is applied for too long, so be careful!
you notice an abnormality in the AC power adaptor, disconnect it from
Y Strong viscosity
the AC outlet immediately.
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
Y Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
SAFETY-RELATED COMPONENT WARNING!!ATTENTION AU COMPOSANT AYANT RAPPORT
� LA S?CURIT?!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITHLES COMPOSANTS IDENTIF?S PAR UNE MARQUE 0 SUR LES
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTSDIAGRAMMES SCH?MATIQUES ET LA LISTE DES PIéCES SONT
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESECRITIQUES POUR LA S?CURIT? DE FONCTIONNEMENT. NE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERSREMPLACER CES COMPOSANTS QUE PAR DES PIéSES SONY
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTSDONT LES NUM?ROS SONT DONN?S DANS CE MANUEL OU
PUBLISHED BY SONY.DANS LES SUPP?MENTS PUBLI?S PAR SONY.
2 |
ACEC
