HCD-DX30/RG40
SECTION 4
TEST MODE
[MC Cold Reset][Change-over of AM Tuner Step between 9 kHz and
Y The cold reset clears all data including preset data stored in the10 kHz]
RAM to initial conditions. Execute this mode when returningY A step of AM channels can be changed over between 9 kHz and
the set to the customer.10 kHz.
Procedure:Procedure:
1. Press three buttons x , ENTER , and ?/1 simultaneously.1. Press ?/1 button to turn the set ON.
2. The fluorescent indicator tube displays OCOLD RESET� and2. Select the function OTUNER�, and press TUNER/BAND
the set is reset.button to select the BAND OMW�.
3. Press ?/1 button to turn the set OFF.
[CD Ship Mode]4. Press ENTER and ?/1 buttons simultaneously, and the display
Y This mode moves the pickup to the position durable to vibra-of fluorescent indicator tube changes to OAM 9 k STEP� or
tion. Use this mode when returning the set to the customer afterOAM 10 k STEP�, and thus the channel step is changed over.
repair.
Procedure:[GC Test Mode]
1. Press 1/u button to turn the set ON until OSTANDBY�Y This mode is used to check the software version, FL tube, LED,
appears.keyboard, headphone and volume.
2. Press CD button and 1/u button simultaneously.Procedure:
3. When you releaset he buttons, a message OLOCK� is displayed1. Press three buttons x , ENTER and DISC 2 simultaneously.
on the fluorescent indicator tube, and the CD ship mode is set.2. LEDs and fluorescent indicator tube are all turned on.
3. When ENTER and DISC2 are pressed at the same time, the
[MC Hot Reset]key number check mode starts up. In this mode, the key numbers
Y This mode resets the set with the preset data kept stored in theof each key series are displayed.
memory. The hot reset mode functions same as if the power4. In the key check mode, the fluorescent indicator tube displays
cord is plugged in and out.OKEY 000�. Each time a button is pressed.
Procedure:5. When ENTER and DISC2 are pressed at the same time, the
1. Press three buttons x , ENTER , and DISPLAY simultaneously.key count check mode starts up. In this mode, the message OKEY
2. The fluorescent indicator tube becomes blank instantaneously,CNT @@� is displayed on the FL display tube. When each
and the set is reset.button is pressed, the key row number is incremented first. Then
the key value is then incremented. However, one the button is
[CD Service Mode]pressed, the key value cannot be counted.
Y This mode can run the CD sled motor freely. Use this mode, for6. When ENTER and DISC2 are pressed at the same time, the
instance, when cleaning the pickup.headphones check mode starts up. In this mode, the message
Procedure:OH_P ON� is displayed when the headphones are inserted. When
1. Press ?/1 button to turn the set ON.the headphones are not inserted. the message OH_P OFF� is
2. Select the function OCD�.displayed.
3. Press three buttons x , ENTER , and OPEN/CLOSE simul-7. When ENTER and DISC2 are pressed at the same time, the
taneously.volume check mode starts up. In this mode, the message
4. The CD service mode is selected.OVOLUME FLAT� is displayed on the FL display tube. When
5. With the CD in stop status, turn the shuttle knob clockwise tothe volume control knob is rotated in the positive (+) direction,
move the pickup to outside track, or turn the shuttle knobthe message OVOLUME UP� is displayed. When the volume
counter-clockwise to inside track.control knob is rotated in the negative (-) direction, the message
6. To exit from this mode, perform as follows:OVOLUME DOWN� is displayed.
1) Move the pickup to the most inside track.8. In order to quit the mode, either press ENTER and DISC2 at
2) Press three buttons in the same manner as step 2.the same time or press the three buttons at the same time as in
Note: Y Always move the pickup to most inside track when exiting fromstep 1.
this mode. Otherwise, a disc will not be unloaded.9. To exit from this mode, press three buttons in the same manner
Y Do not run the sled motor excessively, otherwise the gear can beas step 1, or disconnect the power cord.
chipped.
13 |
ACEC
