HCD-DZ110/DZ111/DZ120/DZ120K
SECTION 4Ver. 1.4
TEST MODE
3. Disc Tray Lock
Note 1: Regarding the notification symbol OR�The disc tray lock function for the antitheft of an demonstration
Because the number of the operating buttons of this product
are limited, some operations require use of the operatingdisc in the store is equipped.
buttons of the remote commander, When a specific operationSetting Procedure :
requires use of the operating buttons of the remote1. Press the ?/1 button to turn the set on.
commander, OR� is added to the specific operating procedur2.Press the FUNCTION beutton to set DVD function.
in this manual. Example MENU/NO OR� The MENU/NO3. Insert a disc.
button of remote commander.4. Press the x button and the A button simultaneously for five
Note 2: Incorrect operations may be performed if the test mode isseconds.
not entered properly.5. The message OLOCKED� is displayed and the tray is locked.
In this case, press the ?/1 button to turn the power off, and
retry to enter the test mode.Releasing Procedure :
1. Press the x button and the A button simultaneously for five
seconds again.
2. The message OUNLOCKED� is displayed and the tray is1. Cold Reset
Y The cold reset clears all data including preset data stored in
unlocked.the RAM to initial conditions. Execute this mode when
Note: When OLOCKED� is displayed, the slot lock is not released byreturning the set to the customers.
turning power on/off with the ?/1 button.
Procedure:
4. DVD Ship Mode1. Press the ?/1 button to turn the power on.
2. Press three b xuttons , A and ?/1 simultaneously.
Y Use this mode when returning the set to the customer after3. When this button is operated, display as OCOLD RESET� for
repair.
Procedure:a while and all of the settings are reset.
2. Panel Test Mode1. Press the ?/1 button to turn the set on.
YThis mode is used to check the software version, FL, LED2. Press the FUNCTION button to set the function ODVD�.
and KEY.3. Remove all discs, and then press tw x and o b .uttons
simultaneously.
2-1. Display Test Mode4. After a message OMECHA LOCK� is displayed on the
Procedure:fluorescent indicator tube, pull out the AC plug.
1. Press the ?/1 button to turn the power on.5. To exit from this mode, press the ?/1 button to turn the set on.
2. Press three bXuttons , . and A simultaneously.
3. When the display test mode is activated, all se5.gments and LEDs AM Step Change
are turned on.YA step of AM channels can be changed over between 9 kHz
4. To exit from this mode, press three bX , . and uttons Aand 10 kHz.
simultaneously.Procedure:
1. Press the ?/1 button to turn the set ON.
2-2. Version Test Mode
2. Select the function OTUNER�, and press FUNCTION button
to select the BAND OAM�.Procedure:
3. Press the ?/1 button to turn the set OFF.1. When the display test mode is acti.vated, press the button
4. Press two buttons > and ?/1 simultaneously, and theand the message ODSX1� (DZ110), ODSX1-� (DZ111),
ODSX1+� (DZ120), ODSX1K� (DZ120K) are displayed, the
display of fluorescent indicator tube changes to OAM 9 k
STEP� or OAM 10 k STEP�, and thus the channel step isversion test mode is activated.
changed over.2. Whenever the . button is pressed, the display changes in
the following order.
*1
ODSX1� (Model name) t OCE2 � (Destination) t MC 6. Volume Test Mode
Procedure:
1. Press the ?/1 button to turn the power on.TM T DSP T TA T ST T DVD T UI T SYS
2. Press three b.uttons , H and > simultaneously.*1: CE2 changes depending on destination.
3. Press the > button and the date of the software production
3. The message OVOLUME MAX� is displayed, when the
VOLUME control is turned in the dirction of (+).is displayed.
The message OVOLUME MIN� is displayed, when the4. Press the > button again and the version is displayed.
VOLUME control is turned in the dirction of (�).5. To exit from this mode, press three bX , . and uttons A
simultaneously.
4. To exit from this mode, pr ?/1ess the button to turn the set off.
2-3. Key Test Mode
7. Product Out
This mode moves the optical pick-up to the position durable toProcedure:
1. When the display test mode is actiHva buted, press the tton,
vibration and clears all data including preset data stored in the RAMto select the key test mode.
to initial conditions. Use this mode when returning the set to the2. To enter the KEY test mode, the fluorescent indicator displays
customer after repair.
Procedure:OK0 V0�. Each time a button is pressed, OKEY� value
increases. However, once a button is pressed, it is no longer
1. Press the ?/1 button to turn the power on.taken into account. When all keys are pressed correctly, OK8
2. Press the FUNCTION button to set the function ODVD�.V0� is displayed.
3. Remove all discs, and then press three buttons > , A and
?/1 simultaneously.3. When the VOLUME control is turned in the direction of (+),
OV0� is changed to OV1�, then ... OV9�.
4. After the OSTANDBY� blinking display finishes, the messageWhen the VOLUME control is turned in the direction of (�),
OMECHA LOCK� is displayed on the fluorescent indicatorOV0� is changed to OV9�, then ... OV1�.
tube disconnect the AC power plug, then the ship mode is set.
4. To exit from this mode, press three bX , . and uttons A
simultaneously.
19 |
ACEC
