HCD-FC7
2-3. Track/Layer Jump2-5. EEPROM Write Adjust
Track/Layer JumpEEPROM Write Adjust
1. 1TjFWD R.Lj L0>L1
2. 1TjREV L.Lj L1>L0 1. Focus Offset
3.500Tj FineFWD U.Fj L0>L1 2. Focus Gain
4.500Tj FineREV D.Fj L1>L0 3. Trk.Offset Coarse
5.10kTj DircFWD 4. NNNNNN
6.10kTj DircREV 5. Trk.Gain
7.20kTj DircFWD 6. EQBoost
8.20kTj DircREV
0.All Servo Off
0. All Servo Off
Exit: RETURNExit: RETURN
On this screen, each item can be adjusted automatically. Select the
On this screen, track jump, etc. can be performed. Only for the DVDdesired number [1] to [10/0] from the remote commander, and
dual layer disc, the focus jump and layer jump are displayed in theselected item is adjusted automatically.
right field
[1] Focus Offset:Adjusts focus offset.
[1] 1Tj FWD:1 track jump forward.[2] Focus Gain:Adjusts focus gain.
[2] 1Tj REV:1 track jump reverse.[3] TRK. Offset:Adjusts tracking offset of the RF amp
[3] 500Tj FWD:500 track jump (fine search)forward.(IC001) side.
[4] 500Tj REV:500 track jump (fine search) reverse.[5] TRK. Gain:Adjusts track gain.
[5] 10kTj FWD:10k track jump (direct search) forward.[6] EQ Boost: Adjusts amount of boost of equalizer.
[6] 10kTj REV:10k track jump (direct search) reverse.[10/0]: All servo off.
[7] 20kTj FWD:20k track jump (direct search) forward.
[8] 20kTj REV:20k track jump (direct search) reverse.2-6. Memory Check
[10/0]: All servo off.Display images are shown as follows, and all two screens are able
to switch by the O key (UP) or o key (DW).
2-4. Non EEPROM Write Adjust
EEPROM Data 1/2CD SL L0 L1
Non EEPROM Write AdjustFocus Gainxx xx xx xx
Trk.Gainxx xx xx xx
1. Focus OffsetFocus Offsetxx xx xx xx
2. Focus GainTrk.Offsetxx xx xx xx
3. Trk. Offset CoarseEQ.Boostxx xx xx xx
4. Trk. Offset FinePILevelxx xx -- --
5. Trk. GainFcs. Balance-- xx -- --
6. EQBoostJitterxx xx xx xx
Mirror Timexx xx xx --
0.All Servo OffFE Level-- xx -- --
Traverse Lv1.-- xx -- --
Next:DW Default:CLRExit:RET
Exit: RETURN
EEPROM Data 2/2CDRW DVDRW
On this screen, each item can be adjusted manually. Select the desiredFocus Gainxxxx
number [1] to [10/0] from the remote commander, and currentTrk.Gainxxxx
setting for the selected item will be displayed, then increase orFocus Offsetxxxx
decrease numeric value with the O key or o key. This value isTrk.Offsetxxxx
stored in the EEPROM. If CLV has been applied, the jitter isEQ.Boostxxxx
displayed for reference for the adjustment.
[1] Focus Offset:Adjusts focus offset.
[2] Focus Gain:Adjusts focus gain.
[3] TRK. Offset:Adjusts tracking offset of the RF amp
(IC001) side.
[4] TRK. Offset:Adjusts tracking offset of the DSP (IC401)Prev:UP Default:CLRExit:RET
side.
[5] TRK. Gain:Adjusts track gain.On this screen, current servo adjusted data stored in the EEPROM
[6] EQ Boost: Adjusts amount of boost of equalizer.are displayed. The adjusted data are initialized by pressing the
[10/0]: All servo off.[CLEAR] key, but be careful that they are not recoverable after
initialization.
Before clearing the adjusted data, make a note of the set data. This
screen will also appear if [0]-All is selected in the Drive Auto
Adjustment. In this case, default setting cannot be made.
31 |
ACEC
