SONY HCDVP700 Repair Manual

$7.99

SONY HCDVP700 - It's a complete service manual, and it's in PDF format. It contains circuit diagrams ( schemas ) etc. It also usually contains parts catalog. After placing order we'll send You download instructions on Your email address. See below for delivery information

The manual is available only in language(s): English

Link to manual will be sent on Your email address after You place order.

This product was added to our catalog on Monday 07 May, 2007.

Reviews

Write Review

Buy & Download

Product Reviews

There are currently no reviews for this product.

Other reviews

Grace Towers - 05/22/2008

Very nice clear manual with specifications, exploded views and schematics, been searching for one of these for years. Thanks.

Glen Meyer - 10/26/2008

Very fast service, manual is well scanned and clear, but the Appendix A containing PC Command table and Control codes are missing

Henry Seiden - 02/26/2009

I downloaded this product and looked through it quickly with Adobe Reader v9. It is clean and a good copy. Some scanned pages are not perfectly square, but that is a minor complaint. The document schematics and board diagrams are easy to read, of good contrast. The whole file downloaded quickly. This is a good service! Sony charges about $100 for the printed version of the same manual. It is still available through their print-on-demand pro parts system, but why would you do that?

Dutra Lacerda - 02/17/2008

All schematics for the Euro-PC and some extra info. Needed if you want to replace some missing hardware. A piece of great historical value and for vintage computing entusiasts.

Roger Mason - 07/28/2006

Man, I was looking for this manual for a while! Where do You get them?;) Of course, quality is goooood:) Anyway, I can only say: A+A+A+!

Customers who bought this product also purchased

SONY 1400 Service Manual	SONY 362B Service Manual	SONY 710BK-AL Service Manual
SONY 1401 Service Manual	SONY 16229172 Service Manual	SONY AC-V25A Service Manual

Click to see text excerpt from the manual

HCD-VP700
[VCD COLOR SYSTEM MODE][VIDEO BOARD] (SIDE A)
Y This mode is used for changing the COLOR SYSTEM of the
VCD.
Procedure:1 2 3
J302
1. Set the standby mode.
J301
2-1.Press the two buttons `/1 and > simultaneously to set the
COLOR SYSTEM of the VCD to AUTO.
2-2.Press the two buttons `/1 and . simultaneously to fix the
COLOR SYSTEM of the VCD to PAL.
2-3.Press the two buttons `/1 and X simultaneously to fix the
COLOR SYSTEM of the VCD to NTSC.
3. The power tune ON automatically and the function sets toOCDOO.
4. The FL tube shows the COLOR SYSTEM mode see .
5. The COLOR SYSTEM mode set is maintained (memorized)
until COLD RESET is executed.
CN501
[VIDEO CD Color-bars Mode]
On this mode, the data of the color-bars signal as a picture signal
and the 1 kHz sine wave signal as a sound signal are output by the
mechanism controller (IC502) for the video CD signal check. When
measurement of the voltage and waveform on the VIDEO board,
perform it in this mode.
For reference, the color-bars signal can be observed at J302 usingSL503
an oscilloscope.SL502
Procedure:SL501
1. Short the both ends of the land of SL503 of the VIDEO board.
CN503
2. Turn the power on. Press the CD button to select CD.
CHECK LED
3. The color-bars appears when the CD is in stop status, and it
disappears when the CD goes in play status.
4. After measuring, remove the lead wire connected.VIDEO boardCN502
(SIDE B)
[CD Servo ON/OFF Mode]
Procedure:
1. Short SL502 on the VIDEO board by soldering.
2. Turn on the main power. Set a disc on the DISC1 tray. Select
CD.
3. Press the hH button to play back CD.
4. When the > button is pressed, 100 track jump is executed.
5. Also, every pressing of the PLAY MODE button triggers
between ON and OFF of TRACKING SERVO and SLED
SERVO.
How to quit the CD servo ON/OFF mode:
1. Press the ?/1 button to turn off the main power.
2. Remove soldering from SL502.
[REPEAT 5 LIMIT OFF MODE]
Y This mode is used to enable infinite repetitions.
Normally, the number of repetitions allowed is 5.
Procedure:
1. Press the `/1 button to turn ON the power supply.
2. Set the function OCDÃ�.
3. Press the three burtons ENTER , DISC 3 , and x is
simultaneously.
4. Infinite repetitions is enabled.
5. This state is maintained ( memorized ) until COLD RESET is
executed.
15