The operating instructions mentioned here are partial abstracts SECTION 1
from the Operating Instruction Manual. The page numbers of
the Operating Instruction Manual remain as in the manual.GENERAL
Use of the tilt-swivel
PrecautionsIdentifying parts and controls
This monitor can be adjusted within the angles shown below. To
turn the monitor vertically or horizontally, hold it at the bottom
Warning on power connectionsSee the pages in parentheses for further details. GDM-F500 is with both hands.
Y Use the supplied power cord. If you use a different power cord, used for illustration purposes throughout this manual.
be sure that it is compatible with your local power supply.FrontRearGDM-F400
For the customers in the U.S.A.
If you do not use the appropriate cord, this monitor will not 90u
conform to mandatory FCC standards.12u
Example of plug types90u
RGBHDVD
5u(HD15)(BNC)
RESETASCINPUTHD15BNCMENU
for 100 to 120 V ACfor 200 to 240 V AC
GDM-F500
Y Before disconnecting the power cord, wait at least 30 seconds
after turning off the power to allow the static electricity on the
screenOs surface to discharge.90u
Y After the power is turned on, the screen is demagnetized 15u
(degaussed) for about 3 seconds. This generates a strong
90u
magnetic field around the screen which may affect data stored 1 RESET button (page 14)9 Video input 1 connector (HD15) (page 6)
on magnetic tapes and disks placed near the monitor. Be sure to 5uThis button resets the adjustments to the factory settings.This connector inputs RGB video signals (0.700 Vp-p,
keep magnetic recording equipment, tapes, and disks away positive) and sync signals.
from the monitor.2 ASC (auto sizing and centering) button (page 9)
This button automatically adjusts the size and centering of the 5 4 3 2 1
The equipment should be installed near an easily accessible picture.10 9 8 7 6EN
1-1outlet.
15 14 13 12 11
3 INPUT button and HD 15/BNC indicators (page 9)
Installation This button selects the HD15 or BNC video input signal. The
input signal and corresponding input indicator change each Pin No.Signal
Do not install the monitor in the following places:
time you press this button.
Y on surfaces (rugs, blankets, etc.) or near materials (curtains, 1Red
draperies, etc.) that may block the ventilation holes4 Joystick (page 11)2Green
Y near heat sources such as radiators or air ducts, or in a place
The joystick is used to display the menu and make (Composite Sync on Green)
subject to direct sunlight
adjustments to the monitor, including brightness and contrast
Y in a place subject to severe temperature changes3Blue
adjustments.
Y in a place subject to mechanical vibration or shock4ID (Ground)
Y on an unstable surface5 1 (power) switch and indicator (pages 7, 15, 18)5DDC Ground*
Y near equipment which generates magnetism, such as a This button turns the monitor on and off. The power indicator
transformer or high voltage power lines6Red Ground
lights up in green when the monitor is turned on, and either
Y near or on an electrically charged metal surface7Green Ground
flashes in green and orange, or lights up in orange when the
monitor is in power saving mode.8Blue Ground
Maintenance
Y Clean the screen with a soft cloth. If you use a glass cleaning 6 AC IN connector (page 7)9DDC + 5V*
liquid, do not use any type of cleaner containing an anti-static This connector provides AC power to the monitor.10Ground
solution or similar additive as this may scratch the screenOs
coating.7 USB (universal serial bus) upstream connector 11ID (Ground)
Y Do not rub, touch, or tap the surface of the screen with sharp or (page 8)12Bi-Directional Data (SDA)*
abrasive items such as a ballpoint pen or screwdriver. This type Use this connector to link the monitor to a USB compliant 13H. Sync
of contact may result in a scratched picture tube.computer.
Y Clean the cabinet, panel and controls with a soft cloth lightly 14V. Sync
moistened with a mild detergent solution. Do not use any type 8 USB (universal serial bus) downstream connectors 15Data Clock (SCL)*
of abrasive pad, scouring powder or solvent, such as alcohol or (page 8)
benzene.Use these connectors to link USB peripheral devices to the * DDC (Display Data Channel) is a standard of VESA.
monitor.
Transportationq; Video input 2 connector (BNC) (page 6)
This connector inputs RGB video signals (0.700 Vp-p,
When you transport this monitor for repair or shipment, use the
positive) and sync signals.
original carton and packing materials.
45 |
ACEC
