TOSHIBA FT7007LBR Repair Manual

$7.99

TOSHIBA FT7007LBR - It's a complete service manual, and it's in PDF format. It contains circuit diagrams ( schemas ) etc. It also usually contains parts catalog. After placing order we'll send You download instructions on Your email address. See below for delivery information

The manual is available only in language(s): English

Link to manual will be sent on Your email address after You place order.

This product was added to our catalog on Monday 07 May, 2007.

Reviews

Write Review

Buy & Download

Product Reviews

There are currently no reviews for this product.

Other reviews

HIROSHI EMOTO - 11/29/2007

Very fast service and a good documents. Thank you.

Paul Brady - 01/03/2007

Talk about a lifesaver!!!!!!!!!!!! This schematic will also work for the Radio Shack DX-392. This is the full blown service manual complete with alignment instructions, schematics, and parts lists.

Grace Towers - 05/22/2008

Very nice clear manual with specifications, exploded views and schematics, been searching for one of these for years. Thanks.

Jason Gaunt - 01/26/2008

This manual is for both the EU and Australian version of the CCD-TR55(E) Camcorder, as stated it includes both the users manual and the service manual. The quality of the manual is very good but it is only black and white (not full colour) and ultimately it is just a scan, so 4/5 from me.

Aaron Lawrence - 01/02/2008

Contains mechanism diagrams, parts lists and schematics for all worldwide versions of DC-X88Z. Also includes remote schematic etc. A few non-essential pages are missing such as specifications. Includes the mechanical and electronic calibration instructions for the tape decks.

Customers who bought this product also purchased

TOSHIBA 1441 Owner's Manual	TOSHIBA 14N21BS Service Manual	TOSHIBA 1451 Service Manual
TOSHIBA 147R7E Service Manual	TOSHIBA 12220T Service Manual	TOSHIBA 12220 Service Manual

Click to see text excerpt from the manual

Receiver
Test Equipment Required and Connections
SG: RF Signal Generator, 46.770MHz Dummy Load, 150-ohm
Noise Meter DC Power Supply: 2.4 V
Digital Voltmeter SINAD Meter
PORTABLENOISE METER
SGDummy Load
(150-ohm)
RF TestSP
PointTerminal
Batt Terminal
MOD=1kHz
DEV=?3kHz
DC Power SupplyDigital Voltmeter Balance Input
SINAD
Meter
2.4V
Preset
Turn Power On (Connect Battery) while depressing " a" and " # " keys. A beep will be heard.

Alignment Procedure
StepPreset toAdjustmentRemarks
Press the " 1 " key, then the TX Mode is entered.
SG: 1mV
1L503Set the digital voltmeter at the test point of RX VCO (See page 25),
No modulation
then adjust L503 to indicate DC 2.0 V ?0.05V.
Press the ? 4 ? key, then the RX Adjust Mode is entered.
SG: 1mV
2L502Connect SG to RF Test Point. Set the digital voltmeter to the DISCRI
No modulation
Test Point. Adjust L502 to indicate DC 0.9V ?0.05V.
SG: 1mV
Connect the NOISE METER to the SP Terminal through a 150-ohm
31kHz ?3kHzRT502
dummy load, then adjust RT502 to indicate 140 ?5 mV.
deviation
Press the ?MEMO? key, then the SQ Adjust Mode is entered.
SG: 0.09"VConnect SG to RF Test Point. Turn RT501 to fully clockwise and
41kHz ?3kHzRT501confirm the Ringer SP501 does not ring.
deviationAdjust RT501 to turn to counter clockwise slowly where the ringer
SP501 rings.
Alignment Point Location Main PCB
DISCRI Test PointRF Test PointRX VCO Test Point
RT502
L503
L502
RT501
6