English
Accessories17* Adjust suction power using the suction control on the Replacing the motor filter (Ref. No. EF54)48 Remove the nozzle from the vacuum cleaner tube and
remove entangled threads etc. by snipping them away with
1 Dustbag, s-bagTM, 6* Parquet nozzlevacuum cleaner or the suction control on the hose handle.Should be done with every 5th replacement of the dust bag,
scissors. Use the hose handle to vacuum the nozzle.
s-bagTM Clinic7* Power nozzle18 A practical parking feature (as well as minimizing the risk of s-bagTM
2* Telescopic tube8* Turbo nozzlebackache) makes things easier when pausing during clean-32 Depress the catch and open the lid.Troubleshooting
3* Extension tube (2)9 Crevice nozzleing.33 Remove the old filterThe vacuum cleaner does not start
4 Hose handle10 Upholstery nozzle
19 The parking feature makes it easier to move and store the 34 Insert a new filter and close the lid.1 Check that the cable is connected to the mains.
5 Carpet/hard floor
vacuum cleaner.2 Check that the plug and cable are not damaged.
nozzleTakingcareofthefilters 3 Check for a blown fuse.
Use the nozzles as follows:The more often the better for the efficiency of the cleaner.
The vacuum cleaner stops
SafetyprecautionsCarpets: Use the carpet/hard floor nozzle with the There are four types of exhaust filter, depending on the vacuum TM
Clario should only be used by adults and only for normal vacuum-lever in position (20). Reduce suction power for small carpets.cleaner model:1 Check whether the dust bag, s-bag is full. If so, replace it
ing in a domestic environment. The vacuum cleaner features ? Hepa H12 washable (Ref. No. EFH12W)with a new one.
Hard floors: Use the carpet/hard floor nozzle wit 2 Is the nozzle, tube or hose blocked?
double insulation and does not need to be earthed.? Hepa H12 non washable (Ref. No. EFH12)
the lever in position (21).3 Are the filters blocked?
? Microfilter with frame (Ref. No. EF17)
Never vacuum:
Wooden floors: Use the parquet nozzle (certain models only, 6).? Microfilter (Ref. No. EF2)Water has entered the vacuum cleaner
? In wet areas.
It will be necessary to replace the motor at an authorised AEG-
? Close to flammable gases, etc.Upholstered furniture: Use the upholstery nozzle (10).Replacement of the microfilter and the non-washable
Electrolux service centre. Damage to the motor caused by the
? Without an s-bagTM (this may damage the Crevices, corners, etc.: Use the crevice nozzle (9).HEPA filter
penetration of water is not covered by the warranty.
cleaner). The filters must always be replaced with new ones and cannot
Using the power socket (requires a Clario equipped with a
A safety device is fitted which prevents the cover be washed.Consumerinformation
designated power socket. The power nozzle is available as an
closing without an s-bagTM. Do not attempt to 35 Open and remove the lid, remove the filter (every fifth bag AEG-Electrolux decline all responsibility for all damages arising
accessory.)
force cover shut.change).from any improper use of the appliance or in cases of tampering
22 Attach the nozzle to the tube (certain models only).
with the appliance.
Never vacuum:36 Insert a new filter and replace the lid as shown in the picture.
23 Connect the power nozzle to the socket on the vacuum
? Sharp objects.Cleaning the washable HEPA filter This product is designed with the environment in mind. All
cleaner.
? Fluids (this can cause serious damage to the (ref. no. EFH12W, some models only)plastic parts are marked for recycling purposes. For details see
24 Use the clips to secure the cable along the tubes and hose.
machine).Should be done with every 5th replacement of the dust bag, our web site:
25 The power nozzle starts operating when the vacuum
? Hot or cold cinders, lit cigarette butts, etc.s-bagTMwww.electrolux.de
? Fine dust from plaster, concrete, flour or ash, cleaner is switched on.
37 Open and remove the lid, then remove the filter.
for example. The above can cause serious damage Using the turbo nozzle (certain models only)
38 Rinse the inside (dirty side) of the filter in warm tap water.
to the motor damage which is not covered by 26 Attach the nozzle to the tube.
Tap the filter frame to remove excess water. Repeat four
the warranty.
27 Adjust the suction power by opening or closing the air vent.times and allow the filter to dry. Note: Do not use cleaning
Electrical cable precautions:agents and avoid touching the delicate filter surface.
? A damaged cable must be replaced by an authorised AEG-Note: Do not use the power or turbo nozzle on fur rugs, rugs with 39 Replace the filter and lid as shown.
Electrolux service centre. Damage to the cleaner cable will long fringes or a pile depth exceeding 15 mm. To avoid damaging Cleaning the hose and nozzle
not be covered by the warranty.the carpet, do not keep the nozzle stationary whilst the brush The vacuum cleaner stops automatically if the nozzle, tube, hose
? Never pull or lift the vacuum cleaner by the cable.is rotating. Do not pass the nozzle across electric cables, and be or filters and s-bagTM becomes blocked. In such cases, disconnect
? Disconnect the plug from the mains before sure to switch off the vacuum cleaner immediately after use.from mains and allow to cool for 20-30 minutes. Clear blockage
cleaning or maintenance of the vacuum cleaner.Replacingthes-bagTM/cleningthefilterand/or replace filters and s-bagTM and restart.
? Regularly check that the cable is not damaged.
28 The dust bag, s-bagTM must be replaced when the indicator Cleaning tubes and hoses
Never use the vacuum cleaner if the cable is
window is completely red. Read the indicator with the floor 40 Use a cleaning strip or similar to clear the tubes and hose.
damaged.
nozzle lifted up from the carpet.41 It may also be possible to remove the obstruction in the
All service and repairs must be carried out by an authorised
29 Remove the hose and open the lid.hose by squeezing it. However, be careful in case the
AEG-Electrolux service centre.
30 Pull the cardboard holder to remove the s-bagTM. This auto-obstruction is caused by glass or needles caught inside the
Always keep the vacuum cleaner in a dry place.
matically closes the dust bag and stops dust from leaking hose.
Beforestartingout.Note: The warranty does not cover any damage to the hose
11 Check that the s-bagTM dustbag and motor filter are in 31 Insert a new s-bagTM by pushing the cardboard holder caused by cleaning it.
place.straight down in its tracks. Close the lid.Cleaning the floor nozzle
TM
12 Insert the hose until the catch clicks to engage (press the Note: Replace the s-bag even if it is not full (it may be blocked). 42 To avoid deterioration of suction power, frequently clean the
catch to release the hose).Also replace after using carpet-cleaning powder. Use only AEG-carpet/hard floor nozzle. The easiest way to clean it is by
Electrolux original dust bags using the hose handle.
13 Attach the extension wand or telescopic wand (only on TMTMTM
s-bag Classic, s-bag Clinic or s-bag Anti-odour.
certain models) to the hose handle and floor nozzle (to take Cleaning the power nozzle (certain models only)
them apart again, twist and pull).43 Disconnect from the mains, and remove entangled threads
etc. by snipping them away with scissors.
14 Extend the cord and plug it into the wall socket.
44 Use a screwdriver to remove the nozzle cover.
The vacuum cleaner has an integrated cord winder.
45 Remove the brush cylinder and bearings, then clean as
15 Press the foot pedal to rewind the cable (take hold of the necessary.
plug to prevent it striking you).46 To clean the wheels, gently lever them from their mountings
16 Press the On/Off button with the foot to start the vacuum and clean as necessary.
cleaner.47 Replace the cover and make sure it is securely fastened.
Cleaning the turbo nozzle (certain models only)
* Certain models only23 |
ACEC
