GB
After having removed the knob once again, making sure that theDISASSEMBLE OF WORK-TOP
thermostat rod has not been moved, screw slightly the aboIn case it is necessarvey to repair or replace the inside components,
mentioned by-pass screw, to obtain a flame of 3 or 4 mm of length.act as follows:remove the glass lid from its position slipping off it
For butane/propane gas, the adjusting screw must be tight screupwards.wed.
Make sure that the flame does not extinguish passing quicRemokly fromve the grids, remove burners and flame-spreaders (see
the maximum flow to the minimum flow, and closing and openingfig. 13), unscrew the visible screws ?V? placed on the work-top
the oven door (the oven door must be closed softly).(see fig. 14). Disassemble the work-top by unscrewing the 4 rear
Attention: for taps with safety device, the minimum adjusting screscrews ?A? (see fig.w 15 ).
?T? is on the outside of the tap rod (fig. I ).
AB
V
T
Fig. 13Fig. 14
Fig. HFig. I
REGULATION AIR ADJUSTER
REGULATION OF AIR ADJUSTER (oven burner )
To do this,
- Unscrews the screw (A ) in order to rotate the metal ring at the
end of the burner (fig L ).
In this way, entrace of the air increases or descreasesFig., obtaining 15A
a correct flame.
- To disassemble the control panel, unscrew the 4 internal screws
Be sure that the flame does not lift or light back or present a
(B) fixing the control panel to the oven face ( fig 16 ).
yellow colouration .
REGULATION OF AIR ADJUSTER (grill burner )
To do this,
- Unscrews the screw (A ) in order to slip it forwards or backwards
(fig M).Fig. 16C
In this way, entrace of the air increases or descreases, obtainingB
a correct flame.
GREASING OF TAPS
Be sure that the flame does not lift or light back or present a
WARNING:This operation must be carried out by skilled staff.
yellow colouration .
If a tap becomes hard to be turned, grease it using a specific
grease withstanding high temperatures. Act as follows: switch the
appliance off, and close the gas tap open the work-top and
disassemble also the control panel as described on the previous
paragraph. Unscrew the two fixing screws from the burner body
(see picture) and remove the cone.
A
Clean the cone and its slot by means of a cloth soaked with diluent.Z
ASlightly grease the cone with the relevant grease, put it in its slot,
and turn it some times. Remove the cone again, remove the
Fig. LFig. Mexceeding grease making sure the gas entries are not obstructed
by grease residuals. Assemble everything carefully in the opposite
APPLIANCE MAINTENANCEdirection check the connection seal by means of soapy water.
WARNINGSTAPS REPLACEMENT
Isolate the cooker from the electricity supply before attempting toAct as follows: switch the appliance off, and close the general tap
replace the oven lamp.open the work-top and disassemble also the control panel as
The oven lamp used is of a special type withstanding highdescribed on the previous paragraph. Unscrew screw nut D of the
temperatures. To replace it, act as follows: disassembgas tube supplying the ble theurner. Unscrew screw V fixing the tap to
protecting glass (A) and replace the burnt lamp with one of thethe bridle and remove it (see picture).
same type. Reassemble the protecting glass.Note: Every time the tap is replaced, it is necessary to replace the
seal gasket too check the connection seal by means of soapy
water (see picture).
E 14
25 W - 230 V~
T300°C
D15C
V
A7
1010 |
ACEC
