BASIC OPERATIONS
To select the video source
SELECTION OF AUDIO/VIDEO
1 Turn the FUNCTION to select PHONO, CD or AUX.
2 Press the ENTER button to display VIDEO 1.
SOURCE
3 Turn the MULTI JOG to select VIDEO 2 or VIDEO 3.
To change a displayed name for the VIDEO 1
and VIDEO 2
When the VIDEO 1 function is selected, VIDEO 1 is displayed
initially. It can be changed to DVD or MD.
Press the DIGITAL/ANALOG/BAND button while pressing the
ENTER button, then release the ENTER button first.
The displayed name for the VIDEO 2 function can be changed
to VIDEO 2, LD or TV; while the VIDEO 2 function is selected,
press the DIGITAL/ANALOG/BAND button while pressing the
ENTER button, then release the ENTER button first.
To select the OANALOG� or ODIGITAL� (Dolby
Digital Surround) mode of the VIDEO 1, VIDEO
2 or VIDEO 3 function
Press the DIGITAL/ANALOG/BAND button when the VIDEO 1,
VIDEO 2 or VIDEO 3 is selected. The selected mode OANALOG�
1 Select the program source.
or ODIGITAL� appears on the display.
Turn the FUNCTION selector or press the TAPE MONITOR
In the DIGITAL mode: Equipment connected to the OPTICAL
button. The selected function indicator lights in red.
DIGITAL IN terminal is selected as a source for the VIDEO 1 or
VIDEO 3 function, and equipment connected to the COAXIAL
To listen to or watchThe indicator in redDIGITAL IN terminal for the VIDEO 2 function. The DIGITAL
TapeTAPE MONITORindicator lights in red.
In the ANALOG mode:Equipment connected to the VIDEO 1/
RadioTUNER
DVD/MD IN or VIDEO 3 terminals is selected as a source for the
RecordPHONO
VIDEO 1 or VIDEO 3 function, and equipment connected to the
Compact discCDVIDEO 2/LD/TV terminals for the VIDEO 2 function.
Television, etc.AUX
NOTE
VideoVIDEO 1/DVD/MD,
VIDEO 2/LD/TV, VIDEO 3The ODIGITAL� mode changes to the OANALOG,� when pressing
the TAPE MONITOR button.
LD or Cable TVVIDEO 2/LD/TV
MD or DVDVIDEO 1/DVD/MD
When the OOVER LEVEL� indicator lights up
The unit is equipped with the OVER LEVEL indicator. When input
The function to be selected (except PHONO) depends on the
analog signals from the connected equipment are too high to
equipment connected to the input terminals on the rear panel
accept, the indicator lights on the right side of the display. In this
of the unit.
case, adjust the input level as mentioned below so that the
indicator disappears.
To select with the remote control
Press the TAPE MONITOR button or the FUNCTION button
To adjust the sound level of the connected source
repeatedly.
The input sensitivity level of each function can be adjusted
(except the TUNER, VIDEO 1 (DIGITAL), VIDEO 2 (DIGITAL)
NOTEand VIDEO 3 (DIGITAL) functions).
When using a turntable with a built-in equalizer amplifierWhen the sound le, setvel of the connected source is higher or lower
the switch of the equalizer amplifier to off. See the instructionsthan that of the TUNER, adjust it as follows.
of the turntable for further information.
2 Start the selected program source.1 Select the function to be adjusted.
Turn the FUNCTION or press the TAPE MONITOR button
3 Adjust the sound.
and play the source.
2 Press the N or M button repeatedly.
About the video source to the monitor or TV
Selected video source
Adjust the level so that the OOVER LEVEL� indicator does not
light on the display.
V1: VIDEO 1, V2: VIDEO 2, V3: VIDEO 3
Y The level can be adjusted between -6dB (MIN) and +8dB
(MAX) in 2dB steps. Adjust the level so that the sound is
The selected video source is indicated on the display and theoutput at the same level as the TUNER.
video signal through the MONITOR VIDEO OUT jack is outputY The input sensitivity level of the TAPE MONITOR can be
on the TV.adjusted to 0dB or -6dB.
11 ENGLISH |
ACEC
