Location of controlsPlaying a CDListening to the radioRecording
Remote Control (for CSD-XD55 only)1Press CD (direct power-on).1Press RADIO BAND/AUTO PRESET until the band you want appears in the1Press xZ to open the tape compartment and insert a blank tape. Use TYPE I
Inserting a cassetteLoading a CD
(On the remote, press POWER and then press FUNCTION repeatedly until OCd�display (direct power-on).(normal) tape only.
With the side you wantappears in the display.)Each time you press the button, the indication changes as follows:2Select the program source you want to record.
to play facing youSLEEPOFM� t OAM�ZPUSH2Load a CD in the CD compartment.
OPEN/CLOSEFUNCTION SLEEPPOWERTo record from the CD player
2Hold down TUNE + or � until the frequency digits begin to change in the
FUNCTIONPOWER3Press Z PUSH OPEN/CLOSE to close the CD compartment.Press CD and insert a CD (See OPlaying a CD�).
CD/RADIO(AC ONLY)display.
4Press u (N on the remote).To record from the radio
123The player automatically scans the radio frequencies and stops when it finds a
The player plays all the tracks once.Press RADIO BAND/AUTO PRESET and tune in the station you want (See
Number buttons456clear station.
ToPressOListening to the radio�).
789If you can't tune in a station, press the button repeatedly to change the frequencystop playbackx
With the labeled side upMODEstep by step.3Press z to start recording.
MODE0/1010pause playbacku (XXXXX on the remote)(n is depressed automatically.)
Press the button again to resume play after pause.Tip
If the FM broadcast is noisy, press MODE until "Mono" appears in the display and the radio will play inToPress
PAUSE STOP/EJECTFFREWPLAYRECVOLVOL +*,�monaural.stop recordingxZgo to the next track>
.,>go back to the previous track.
CD, RADIO BAND/CDpause recordingX
Display
AU TO PRESET, TAPENxremove the CDZ PUSH OPEN/CLOSEChanging the AM tuning interval (except US and Canadian models)Press the button again to resume recording.
Remote sensorRADIOTUNElocate a point while listening> (forward) or . (backward) while playing until youIf you need to change the AM tuning interval, do this following:BAND
OPR/BATTu(for CSD-XD55 only)XTUNE �,+to the soundfind the point1 While keeping the RADIO BAND/AUTO PRESET button and x button pressed,Tips
Y Adjusting the volume or the audio emphasis will not affect the recording level.
SURROUNDS-BASSdisconnect the AC power cord from the AC outlet.
POWER HEADPHONESZPUSH OPEN/CLOSExS-BASSlocate a point while observing> (forward) or . (backward) in pause until you findBANDY If the AM program makes a whistling sound after you've pressed z in step 3, press MODE to select
2 While keeping the RADIO BAND/AUTO PRESET button and x button pressed,
the displaythe pointthe beat mode (ObEAt 1�, ObEAt 2� or ObEAt 3�) that most decreases the noise.
reconnect the AC power cord to the AC outlet. The tuning interval is changed and
SURROUNDS-BASSOAM 9� or OAM 10� appears in the display for 2 seconds.locate a specific track directly*a number button of the track on the remote.Y For the best results, use the AC power as a power source for recording.
Y To erase a recording, proceed as follows:
* You cannot locate a specific track if "SHUF" or "PGM" is lit in the display. Turn off the indication byAfter changing the tuning interval, you need to reset your preset radio stations.1 Insert a tape with the recording you want to erase.
pressing x.
2 Press TAPE.
Tip3 Press z.
To locate a track numbered over 10, press >10 first, then the corresponding number buttons on thePresetting radio stations
remote.
*The button has a tactile dot.You can store radio stations into the playerOs memory. You can preset up to 30 radio stations, 20
Example:To play track number 23, press >10 first, then 2 and 3.
Adjusting the sound emphasis
for FM and 10 for AM in any order.
1Press RADIO BAND/AUTO PRESET to select the band.
Using the displayTo reinforce the bass sound
2Hold down RADIO BAND/AUTO PRESET for 2 seconds until OAUTO� flashesPress S-BASS.
To check the total track number and playing timein the display.OS-BASS� appears in the display.
To turn on/off the powerPress DISPLAY/ENTER/MEMORY in stop mode (see fig. E).To return to normal sound, press the button again.
Press POWER.3Press DISPLAY/ENTER/MEMORY.
To check the remaining timeThe stations are stored in memory from the lower frequencies to the higher ones.
Press DISPLAY/ENTER/MEMORY repeatedly while playing a CD. The display changes asTo adjust the volume
To get the SURROUND effect
Press VOLUME +, � (VOL +, � on the remote).follows:If a station cannot be preset automatically
VO LUME �,+*You need to preset a station with a weak signal manually.Press SURROUND.
MODESLEEP"SURROUND" appears in the display.t the current track number and playing time
To listen through headphones1 Press RADIO BAND/AUTO PRESET to select the band.
DISPLAY/ENTER/MEMORYSURROUNDr
Connect the headphones to the HEADPHONES jack.You can get the effect of expansion of the sound field.
.,>2 Tune in a station you want.the current track number and the remaining time on the current track*
To return to normal sound, press the button again.
PRESET �,+3 Hold down DISPLAY/ENTER/MEMORY for 2 seconds until the preset number flashes in
r
the display.
TUNE �,+the number of tracks left and remaining time on the CD
4 Press PRESET + or � repeatedly that you want to preset the new station.
Falling asleep to music
5 Press DISPLAY/ENTER/MEMORY.
* For a track whose number is more than 20, the remaining time appears as O- -:- -� in the display.
Display
On the remote (for CSD-XD55 only)1 Play the music source you want.
EF1 Press BAND until the band you want appears in the display.2 Press SLEEP to display OSLEEP.�
Total track numberTotal playing timeProgrammed trackPlaying orderSelecting the play mode3 Press SLEEP to select the minutes until the player goes off automatically.
2 Tune in a station you want.
Press MODE until OREP 1� OREP ALL� OSHUF� OSHUF REP� OPGM� OPGM REP� appears in3 Hold down the number buttons that you want to preset the new station on for about 2 seconds.Each time you press the button, the indication changes as follows: O60� t O90� t O120�
the display. Then proceed as follows:t OOFF� t O10� t O20� t O30�
To select the preset number over 10, press >10 first, then the corresponding number buttons.
ToSelectThen do thisYou need to hold down the last number button to enter for about 2 seconds.To cancel the sleep function
repeat a single trackOREP 1�Press . or > to select the track that you(Example: To select 12, press >10 and 1 first, then hold down 2 for about 2 seconds.)Press POWER to turn off the power.
want to repeat, then press u.
Power SourcesNote
repeat all tracksOREP ALL�Press u.When you are playing a tape using this function:
Playing preset radio stations
Dshuffle playOSHUF�Press u.If the tape length of one side is longer than the set time, the player will not go off until the tape reaches
Bthe end.
repeat tracksOSHUF REP�Press u.1Press RADIO BAND/AUTO PRESET to select the band.
AE
eein random order
2Press PRESET + or �.
E
eEprogram playOPGM�Press . or > then press DISPLAY/ENTER/1to AC IN
EeMEMORY for the tracks you want to program inOn the remote (for CSD-XD55 only)
eEthe order you want up to 20 tracks (see fig. F).1 Press BAND.
e
E2to a wall outletThen press u.2 Press the number buttons to to tune in the stored station.
220-240V
Crepeat programmed tracks OPGM REP�Press . or > then press DISPLAY/ENTER/ To tune in a preset station over 10, press >10 first, then corresponding number buttons.
MEMORY for the tracks you want to program in(Example: To tune in a preset station 12, press >10 and 1 first, and then press 2.)
the order you want up to 20 tracks. Then Press
u.110-127V
VOLTAGE
SELECTOROn the remote (for CSD-XD55 only)Playing a tape
When youOve selected OPGM� or OPGM REP�, press the number buttons for the track you want
up to 20 tracks, then press N.1Press TAPE (direct power-on).
Connect the AC power cord A or insert six size D (R20) batteries (not supplied) into the battery(On the remote, press POWER and then press FUNCTION repeatedly until
Preparing the remote (for CSD-XD55 only) DTo cancel selected play mode
compartment B.
Press MODE until the selected mode disappears from the display.OTAPE� appears in the display.)
Insert two size AA (R6) batteries (not supplied).
Notes
2Press xZ to open the tape compartment and insert a recorded tape. Close the
Y Replace the batteries when the OPR/BATT indicator dims or when the player stops operating.To check the programmed track and playing order in the display
Replacing batterycompartment. Use TYPE I (normal) tape only.
Replace all the batteries with new ones. Before you replace the batteries, be sure to take out the CDTo check the order of tracks before play, press DISPLAY/ENTER/MEMORY.
With normal use, the batteries should last for about six months. When the remote no longer
from the player.Every time you press the button, the track number appears in the programmed order.3Press n.
operates the player, replace all the batteries with new ones.
Y To use the player on batteries, disconnect the AC power cord from the player.
Y When you operate the player on batteries, you cannot turn on the player using the remote.ToPressTo change the current program
Press x once if the CD is stopped and twice if the CD is playing. The current program will bestop playbackxZ
Central American model and South American model only: Adjusting the voltage C
erased. Then create a new program following the programming procedure.fast-forward or rewind the tapem or M
Be sure to set the VOLTAGE SELECTOR (at the bottom) to your local power supply.
Tippause playbackX
TipPress the button again to resume play after pause.
You can record your own program. After youOve created the program, insert a blank tape and press z to
Only for the customers supplied with an AC plug adaptor:
start recording.eject the cassettexZ
Use the supplied AC plug adaptor if the plug of the mains lead does not match your outlet. |
ACEC
