IntroductionAfter you have cleaned or eventual changed the grease filter you should reset the timer by means pushing the
main switch for more than 2 seconds. If the Timer will not by reset manual the electronic will reset after 15 minutes
Read this instruction manual carefully before installing the hood. These instructions are designed to tell you of
the various technical details of your cooker hood and to make you familiar with its use. Since these instructionsautomatically the Timer.
If your cooker hood is supplied with a charcoal filter and is running in the filtering method the saturation of the
cover more than one type of hood within the same series, it may be that reference is made to components that
charcoal filter will be indicated. After 120 hours all buttons except the main switch will flashing and the charcoal
do not form part of the hood that you are installing. The hood may be used as an exhaust or filter hood. If evacuation
is available (exhaust duct or air flue) we recommend using the hood in the exhaust version to discharge all thefilter should be replaced.
It is as well possible to select manual the degree of saturation. By switch off cooker hood and pushing the bottoms
kitchen vapors and odors out-doors. Fittings can vary from country to country. We reserve the right to modify the
2 and 3 temporary for more than 2 seconds:
product without any notice always with the aim of improvements and in compliance with the relevant norm.
Suggestions for using the hood in exhaust position- No flashing light of the bottom: less than 30 working hours
- Flashing light of bottom 1: between 30 and 60 working hours
When an exhaust hood and a heat source requiring ambient air (e.g. gas, oil, coal stoves, etc.) are used at the
- Flashing light of bottom 1 and 2: between 60 and 110 working hours
same time, attention is required because the air necessary for combustion is exhausted from the room through- Flashing light of bottom 1, 2 and 3: more than 110 working hours
the hood and this creates depression. There is no such danger when the maximum depression in the room is 0,04
After you have replaced the charcoal filter you should reset the timer by means pushing the main switch for more
mbar. In this condition no exhaust gas from the heat source is piped. To assure this condition, make openings
in the room which cannot be closed (doors, windows, etc. are not sufficient) and through which the air necessarythan 2 seconds. If the Timer will not by reset manual the electronic will reset after 15 minutes automatically the
Timer.
for combustion can freely flow.
Setting from Exhaust method into Filtering method (only for model HR - Fig.3A)
Note:?All the exhaust ductwork in the apartment or house should be studied. In case of doubts, get advice or
authorization from the person or agency responsible for the building. When using gas burners, gas ovens, etc.To get an efficiency aspiration the cooker hood could work in 2 different methods - Exhaust / Filtering. By setting
the cooker hood into the proper method the electronic will adjust automatically the fan speed to the air resistance
as well as when using the hood in the filter version, these precautions are not necessary.
of the charcoal filter.
N.B. The efficiency of the exhaust hood decreases as the length of the ducts and number of elbows increase.Exhaust Method: By switch off cooker hood and pushing the bottom 1 for more than 3 seconds the
When using the exhaust version, follow these rules: Do not connect the exhaust hood to chimneys, flues, and
cooker hood will set to the exhaust method - confirm by flashing all buttons for 4 times.
air ducts serving the room. Before venting into exhaust flues and ducts no longer in use, ask for the approval of
the person or agency responsible for the building. The evacuated air must not be let into a warm air duct. For theFiltering Method: By switch off cooker hood and pushing the bottom 2 for more than 3 seconds the cooker hood
will set to the filtering method - confirm by flashing all buttons for 8 times.
evacuation of the exhausted air please note ufficial instructions.
Note: The cooker hood is set from the factory into the Exhaust method.
InstallationOperation light and function of saturation indication for the filters
The hood must be mounted over the center of the cooking area. The minimum distance between the cooker andHI (Fig. 3B) - The saturation of the grease filter will be indicated by the operation LED. By switch off cooker hood
the bottom of the hood must be 650 mm for electric cookers and 750 mm for gas cookers.and pushing the bottom T the operation LED will indicate different colours with following meanings:
Warning: If the room contains a flued fuel burning appliance which is not of the "balance flue" type make sureGreen Light: less than 6 working hours
these is an adequate air inlet to the room at all times so that fumes are not drawn down the flue.Yellow Light: between 6 and 12 working hours
N.B. The distances, however, are subject to the safety rules in effect in the various countries. Before drilling theRed Light: more than 12 working hours (the grease filter should be cleaned or eventual changed)
wall make sure that no pipes or cables will be damaged. If there is no outer waste-pipe for the exhaust version,HR (Fig. 3A) - The saturation of the grease filter will be indicated automatically after 20 hours by means with
an air outlet with a diameter of 130 mm or 160 mm must be made through the wall.flashing of the running speed of the cooker hood. That mean the grease filter should be cleaned or eventual
Wall fixing of the cooker hoodchanged.
1) Set the distance between the cooker hob and the hood (Fig. 4).It is as well possible to select manual the degree of saturation. By switch off cooker hood and pushing the bottoms
2) Be careful, using the drilling template, to allow the correct minimum distance between the cooker and the1 and 3 temporary for more than 2 seconds:
bottom of the hood, in particular when ducting to the outside using a pipe passing above the kitchen wall- No flashing light of the bottom: less than 6 working hours
units (Fig. 6).- Flashing light of bottom 1: between 6 and 12 working hours
3) Join the two parts of the flange (Fig. 5/H) using the two screws, and apply the flange to the top of the motor- Flashing light of bottom 1 and 2: between 12 and 18 working hours
unit (Fig. 5/L), using 4 screws (Fig. 5/I).- Flashing light of bottom 1, 2 and 3: more than 18 working hours
4) Drill the holes in the wall to fix the hood, then fix the hood using the two screws and wall plugs (Fig. 5/N).After you have cleaned or eventual changed the grease filter you should reset the timer by means pushing the
5) For a correct installation the hood is provided (in the rear side of its body) with one or two holes 8 mm diam.main switch for more than 2 seconds. If the Timer will not by reset manual the electronic will reset after 15 minutes
into which one or two wall fixing screws must be inserted (Fig. 5/O).automatically the Timer.
6) Ducting version with pipes over wall units: join the two parts of the 90° curve (Fig. 5/G) using the screws,If your cooker hood is supplied with a charcoal filter and is running in the filtering method the saturation of the
and connect the curve to the flange. Connect the extension (Fig. 6/1) and turn the curve until it is pointingcharcoal filter will be indicated. After 120 hours all buttons except the main switch will flashing and the charcoal
in the direction required for ducting. Now connect up the extraction pipes.filter should be replaced.
7) Ducting version with extraction pipes: connect the flange to a pipe ducting to the outside.It is as well possible to select manual the degree of saturation. By switch off cooker hood and pushing the bottoms
8) Re-circulation version: see point 6), but close the pipe openings using the special plastic grids provided2 and 3 temporary for more than 2 seconds:
(Fig. 5/S), making sure that the flow of air is directed upward and not towards the wall.- No flashing light of the bottom: less than 30 working hours
Insure that all parts are properly fixed and that it is impossible to touch moving parts.- Flashing light of bottom 1: between 30 and 60 working hours
N.B.: If the appliance is provided with a 150 mm spigot, please do not fix the exhaust tube by means of screws- Flashing light of bottom 1 and 2: between 60 and 110 working hours
onto the spigot, otherwise the no-return valve could not work proper.- Flashing light of bottom 1, 2 and 3: more than 110 working hours
Installation of the pipesAfter you have replaced the charcoal filter you should reset the timer by means pushing the main switch for more
(valid for exhaust or filter version)than 2 seconds. If the Timer will not by reset manual the electronic will reset after 15 minutes automatically the
1) Fix the bracket (Fig. 5/C) with 2 plugs and screws (Fig. 5/A) in the required hight for the pipe.Timer.
2) Screw the short pipe (Fig. 5/D) with 2 screws on the bracket (Fig. 5/B).Setting from Exhaust method into Filtering method (only for model HR - Fig.3A)
3) Fit the long pipe from the front (Fig. 5/E).To get an efficiency aspiration the cooker hood could work in 2 different methods - Exhaust / Filtering. By setting
4) After inserting the nuts into their housings, fix the long pipe to the hood using the two self-threading screwsthe cooker hood into the proper method the electronic will adjust automatically the fan speed to the air resistance
and working from the inside (Fig. 5/Q).of the charcoal filter.
5) Close the pipe openings using the special plastic grids provided (Fig. 5/S), making sure that the flow of airExhaust Method: By switch off cooker hood and pushing the bottom 1 for more than 3 seconds the cooker hood
is directed upward and not towards the wall.will set to the exhaust method - confirm by flashing all buttons for 4 times.
N.B.: Make sure the supply voltage ratings correspond with those stated on the appliance data plate.Filtering Method: By switch off cooker hood and pushing the bottom 2 for more than 3 seconds the cooker hood
Attention: if the appliance is not provided with a plug or cannot be easily connected to a wall socket, then thewill set to the filtering method - confirm by flashing all buttons for 8 times.
electrical circuit must incorporate a circuit breaker having at least a 3 mm separation between contacts.Note: The cooker hood is set from the factory into the Exhaust method.
Attention: This appliance must be connected to a system equipped with earth or ground plate. The manufacturersLamp Replacement
decline responsibility for problems caused by failure to observe this rule. The wires in the supply cord are coloredIf it has a halogen lamp look out not to touch it with your hands when you replace it. Use a dry and not
as follows: blue = neutral ? brown = linegreasy protection (for example a cloth) in order to avoid a direct contact with skin which could make the
Using the cooker hoodlamp break. Never use lamps with a wattage higher than the one shown on the label inside the hood.
The cooker hood should be switched on either before or at the same as cooking or frying commences. The grease
Safety rules
and carbon filters are more effective if the fan is not switched off immediately after cooking or frying is completed,
but only after a period of some 20-30 minutes. Before using the cooker hood please ensure that all plastic filmsDo not do any flambe cooking underneath the hood. When frying, never leave the pan alone because the
like on metal grease filter an stainless steel ducting are removed.cooking oil could flare up. Clean all the surfaces frequently to avoid danger of fire. This can be done with
User instructionsa cloth or/and with a brush drenched with denatured alcohol or with any other similar substances, except
Working instruction of the cooker hoodfor the button area (Fig. 3A/3B). It is also important to remove and clean or substitute frequently the filter
The cooker hood could be supplied with different operation panels (Fig. 3A-3B) that works in the following way:installed in the hood.
Back Lit Switches HR (Fig.3A)Maintenance
- Main Switch1-2-3 Speed Switches2 - Light Switch
Important: Prior to any maintenance, switch off and disconnect from electrical supply.
The Timer will run if any speed switch is pushed for more than 3 seconds and will stop running the cooker hood
The carbon filter
after 5 minutes.
Multicolour Switches HI (Fig.3B)When a carbon filter is fitted, the air that is sucked in is additionally cleaned by the active carbon particles within
0/1-2-3 Speed Switches L - Light Switch T - Timerthe filter. This filter cannot be cleaned and so needs to be replaced from time to time, approximately every six
The button T-Timer (Fig.3/3C) will activate the booster function for 5 minutes and aftermonths, depending on how frequently the hood is in use.
Replacing the active carbon filter (only for recirculation hoods)
there the hood will return to the last settings. By pushing any speed switch for more than
The filter can be easily removed by pulling downwards the two knobs (Fig. 2/2).Some cooker hoods are supplied
2 seconds the unit will run for 5 minutes in the selected speed and than will shut off the
hood.with the charcoal filter as in Fig. 7/1, to remove the filter push the latches and pull the filter down (Fig. 8)
Operation light and function of saturation indication for the filtersGrease filter
HI (Fig. 3C) - The saturation of the grease filter will be indicated by the operation LED.This absorbs vapor-suspended grease particles and protects the kitchen and furniture from greasy residues. The
By switch off cooker hood and pushing the bottom T the operation LED will indicatefilter should be washed every 10 to 15 days (in normal operating conditions). Dip the filter into a de-greaser
solution or put it in the dish washer. Make sure not to damage the filter, which is made of several layers of thin
different colours with following meanings:
Green Light: less than 6 working hoursalloy, by hitting or crushing it. The aluminium filter will may change colour, that will have no influence of the
Operation light and function of saturation indication for the filtersefficiency of the filter, may it will improve it.
HI (Fig. 3B) - The saturation of the grease filter will be indicated by the operation LED. By switch off cooker hoodReplacing or cleaning the filters
and pushing the bottom T the operation LED will indicate different colours with following meanings:To remove the aluminuim grease filter (Fig. 1), grab the opening tongue at the filter, pull it in your direction and
move the filter downwards. To reinstall it operate reversed.
Green Light: less than 6 working hours
Yellow Light: between 6 and 12 working hoursWhat to do in the case of a defect?
Red Light: more than 12 working hours (the grease filter should be cleaned or eventual changed)In the case of a service call, please give your service agent the following information:
HR (Fig. 3A) - The saturation of the grease filter will be indicated automatically after 20 hours by means withModel
flashing of the running speed of the cooker hood. That mean the grease filter should be cleaned or eventual
Type
changed.
Manuf.-No.
It is as well possible to select manual the degree of saturation. By switch off cooker hood and pushing the bottoms
1 and 3 temporary for more than 2 seconds:You will find this information on the type plate, situated next to the ventilation motor. Enter the numbers
- No flashing light of the bottom: less than 6 working hoursimmediately into the appropriate boxes. This information will enable the service agent to prepare the necessary
- Flashing light of bottom 1: between 6 and 12 working hoursspare parts in advance, so that your cooker hood can be repaired on the first service visit.
- Flashing light of bottom 1 and 2: between 12 and 18 working hoursTechnical data
- Flashing light of bottom 1, 2 and 3: more than 18 working hoursLinking value: motors 1 x 200 W
Lighting: 2 x 20 W
Total value: 240 W / 230 V / 50 Hz
Electric linking: fixed electric cable 0,9 m with safety plug. In case of interventions remove the plug!
Power: 730 m3/h max. |