Introductionfilter will be indicated. After 120 hours all buttons except the main switch will flashing and the charcoal filter should be
Read this instruction manual carefully before installing the hood. These instructions are designed to tell you of thereplaced.
various technical details of your cooker hood and to make you familiar with its use. Since these instructions cover moreIt is as well possible to select manual the degree of saturation. By switch off cooker hood and pushing the bottoms 2
than one type of hood within the same series, it may be that reference is made to components that do not form partand 3 temporary for more than 2 seconds:
of the hood that you are installing. The hood may be used as an exhaust or filter hood. If evacuation is available (exhaust- No flashing light of the bottom: less than 30 working hours
duct or air flue) we recommend using the hood in the exhaust version to discharge all the kitchen vapors and odors- Flashing light of bottom 1: between 30 and 60 working hours
out-doors. Fittings can vary from country to country. We reserve the right to modify the product without any notice- Flashing light of bottom 1 and 2: between 60 and 110 working hours
always with the aim of improvements and in compliance with the relevant norm.- Flashing light of bottom 1, 2 and 3: more than 110 working hours
Suggestions for using the hood in exhaust positionAfter you have replaced the charcoal filter you should reset the timer by means pushing the main switch for more than
When an exhaust hood and a heat source requiring ambient air (e.g. gas, oil, coal stoves, etc.) are used at the same2 seconds. If the Timer will not by reset manual the electronic will reset after 15 minutes automatically the Timer.
time, attention is required because the air necessary for combustion is exhausted from the room through the hood andSetting from Exhaust method into Filtering method (only for model HR - Fig.3A)
this creates depression. There is no such danger when the maximum depression in the room is 0,04 mbar. In thisTo get an efficiency aspiration the cooker hood could work in 2 different methods - Exhaust / Filtering. By setting the
condition no exhaust gas from the heat source is piped. To assure this condition, make openings in the room whichcooker hood into the proper method the electronic will adjust automatically the fan speed to the air resistance of the
cannot be closed (doors, windows, etc. are not sufficient) and through which the air necessary for combustion can freelycharcoal filter.
flow.Exhaust Method: By switch off cooker hood and pushing the bottom 1 for more than 3 seconds the
Note:?All the exhaust ductwork in the apartment or house should be studied. In case of doubts, get advice orcooker hood will set to the exhaust method - confirm by flashing all buttons for 4 times.
authorization from the person or agency responsible for the building. When using gas burners, gas ovens, etc. as wellFiltering Method: By switch off cooker hood and pushing the bottom 2 for more than 3 seconds the cooker hood will
as when using the hood in the filter version, these precautions are not necessary.set to the filtering method - confirm by flashing all buttons for 8 times.
N.B. The efficiency of the exhaust hood decreases as the length of the ducts and number of elbows increase. WhenNote: The cooker hood is set from the factory into the Exhaust method.
using the exhaust version, follow these rules: Do not connect the exhaust hood to chimneys, flues, and air ducts servingOperation light and function of saturation indication for the filters
the room. Before venting into exhaust flues and ducts no longer in use, ask for the approval of the person or agencyHI (Fig. 3B) - The saturation of the grease filter will be indicated by the operation LED. By switch off cooker hood and
responsible for the building. The evacuated air must not be let into a warm air duct. For the evacuation of the exhaustedpushing the bottom T the operation LED will indicate different colours with following meanings:
air please note ufficial instructions.Green Light: less than 6 working hours
Yellow Light: between 6 and 12 working hours
Installation
Red Light: more than 12 working hours (the grease filter should be cleaned or eventual changed)
The hood must be mounted over the center of the cooking area. The minimum distance between the cooker and the
HR (Fig. 3A) - The saturation of the grease filter will be indicated automatically after 20 hours by means with flashing
bottom of the hood must be 650 mm for electric cookers and 750 mm for gas cookers.
of the running speed of the cooker hood. That mean the grease filter should be cleaned or eventual changed.
Warning: If the room contains a flued fuel burning appliance which is not of the "balance flue" type make sure these
It is as well possible to select manual the degree of saturation. By switch off cooker hood and pushing the bottoms 1
is an adequate air inlet to the room at all times so that fumes are not drawn down the flue.
and 3 temporary for more than 2 seconds:
N.B. The distances, however, are subject to the safety rules in effect in the various countries. Before drilling the wall
- No flashing light of the bottom: less than 6 working hours
make sure that no pipes or cables will be damaged. If there is no outer waste-pipe for the exhaust version, an air outlet
- Flashing light of bottom 1: between 6 and 12 working hours
with a diameter of 130 mm must be made through the wall.
- Flashing light of bottom 1 and 2: between 12 and 18 working hours
Wall fixing of the cooker hood
- Flashing light of bottom 1, 2 and 3: more than 18 working hours
1) Set the distance between the cooker hob and the hood (Fig. 4).
After you have cleaned or eventual changed the grease filter you should reset the timer by means pushing the main
2) Be careful, using the drilling template, to allow the correct minimum distance between the cooker and the bottom
switch for more than 2 seconds. If the Timer will not by reset manual the electronic will reset after 15 minutes
of the hood, in particular when ducting to the outside using a pipe passing above the kitchen wall units (Fig. 6).
automatically the Timer.
3) Join the two parts of the flange (Fig. 5/H) using the two screws, and apply the flange to the top of the motor unit
If your cooker hood is supplied with a charcoal filter and is running in the filtering method the saturation of the charcoal
(Fig. 5/L), using 4 screws (Fig. 5/I).
filter will be indicated. After 120 hours all buttons except the main switch will flashing and the charcoal filter should be
4) Drill the holes in the wall to fix the hood, then fix the hood using the two screws and wall plugs (Fig. 5/N).
replaced.
5) For a correct installation the hood is provided (in the rear side of its body) with one or two holes 8 mm diam. into
It is as well possible to select manual the degree of saturation. By switch off cooker hood and pushing the bottoms 2
which one or two wall fixing screws must be inserted (Fig. 5/O).
and 3 temporary for more than 2 seconds:
6) Ducting version with pipes over wall units: join the two parts of the 90° curve (Fig. 5/G) using the screws, and
- No flashing light of the bottom: less than 30 working hours
connect the curve to the flange. Connect the extension (Fig. 6/1) and turn the curve until it is pointing in the direction
- Flashing light of bottom 1: between 30 and 60 working hours
required for ducting. Now connect up the extraction pipes.
- Flashing light of bottom 1 and 2: between 60 and 110 working hours
7) Ducting version with extraction pipes: connect the flange to a pipe ducting to the outside.
- Flashing light of bottom 1, 2 and 3: more than 110 working hours
8) Re-circulation version: see point 6), but close the pipe openings using the special plastic grids provided (Fig. 5/
After you have replaced the charcoal filter you should reset the timer by means pushing the main switch for more than
S), making sure that the flow of air is directed upward and not towards the wall.
2 seconds. If the Timer will not by reset manual the electronic will reset after 15 minutes automatically the Timer.
Insure that all parts are properly fixed and that it is impossible to touch moving parts.
Setting from Exhaust method into Filtering method (only for model HR - Fig.3A)
N.B.: If the appliance is provided with a 150 mm spigot, please do not fix the exhaust tube by means of screws onto
To get an efficiency aspiration the cooker hood could work in 2 different methods - Exhaust / Filtering. By setting the
the spigot, otherwise the no-return valve could not work proper.
cooker hood into the proper method the electronic will adjust automatically the fan speed to the air resistance of the
Installation of the pipes
charcoal filter.
(valid for exhaust or filter version)
Exhaust Method: By switch off cooker hood and pushing the bottom 1 for more than 3 seconds the cooker hood will
1) Fix the bracket (Fig. 5/C) with 2 plugs and screws (Fig. 5/A) in the required hight for the pipe.
set to the exhaust method - confirm by flashing all buttons for 4 times.
2) Screw the short pipe (Fig. 5/D) with 2 screws on the bracket (Fig. 5/B).
Filtering Method: By switch off cooker hood and pushing the bottom 2 for more than 3 seconds the cooker hood will
3) Fit the long pipe from the front (Fig. 5/E).
set to the filtering method - confirm by flashing all buttons for 8 times.
4) After inserting the nuts into their housings, fix the long pipe to the hood using the two self-threading screws and
Note: The cooker hood is set from the factory into the Exhaust method.
working from the inside (Fig. 5/Q).
Lamp Replacement
5) Close the pipe openings using the special plastic grids provided (Fig. 5/S), making sure that the flow of air is
If it has a halogen lamp look out not to touch it with your hands when you replace it. Use a dry and not greasy
directed upward and not towards the wall.
protection (for example a cloth) in order to avoid a direct contact with skin which could make the lamp break.
N.B.: Make sure the supply voltage ratings correspond with those stated on the appliance data plate.
Never use lamps with a wattage higher than the one shown on the label inside the hood.
Attention: if the appliance is not provided with a plug or cannot be easily connected to a wall socket, then the electrical
circuit must incorporate a circuit breaker having at least a 3 mm separation between contacts.Safety rules
Attention: This appliance must be connected to a system equipped with earth or ground plate. The manufacturersDo not do any flambe cooking underneath the hood. When frying, never leave the pan alone because the cooking
decline responsibility for problems caused by failure to observe this rule. The wires in the supply cord are colored asoil could flare up. Clean all the surfaces frequently to avoid danger of fire. This can be done with a cloth or/and
follows: blue = neutral ? brown = linewith a brush drenched with denatured alcohol or with any other similar substances, except for the button area
Using the cooker hood(Fig. 3A/3B). It is also important to remove and clean or substitute frequently the filter installed in the hood.
The cooker hood should be switched on either before or at the same as cooking or frying commences. The grease
Maintenance
and carbon filters are more effective if the fan is not switched off immediately after cooking or frying is completed, but
Important: Prior to any maintenance, switch off and disconnect from electrical supply.
only after a period of some 20-30 minutes. Before using the cooker hood please ensure that all plastic films like on
The carbon filter
metal grease filter an stainless steel ducting are removed.
When a carbon filter is fitted, the air that is sucked in is additionally cleaned by the active carbon particles within the
User instructions
filter. This filter cannot be cleaned and so needs to be replaced from time to time, approximately every six months,
Working instruction of the cooker hood
depending on how frequently the hood is in use.
The cooker hood could be supplied with different operation panels (Fig. 3A-3B) that works in the following way:
Replacing the active carbon filter (only for recirculation hoods)
Back Lit Switches HR (Fig.3A)
The filter can be easily removed by pulling downwards the two knobs (Fig. 2/2).
- Main Switch1-2-3 Speed Switches2 - Light Switch
Grease filter
The Timer will run if any speed switch is pushed for more than 3 seconds and will stop running the cooker hood after
This absorbs vapor-suspended grease particles and protects the kitchen and furniture from greasy residues. The filter
5 minutes.
should be washed every 10 to 15 days (in normal operating conditions). Dip the filter into a de-greaser solution or put
Multicolour Switches HI (Fig.3B)
it in the dish washer. Make sure not to damage the filter, which is made of several layers of thin alloy, by hitting or
0/1-2-3 Speed Switches L - Light Switch T - Timer
crushing it. The aluminium filter will may change colour, that will have no influence of the efficiency of the filter, may
The Timer will run if the timer switch is pushed and will stop running the cooker hood after 5 minutes.
it will improve it.
Operation light and function of saturation indication for the filters
Replacing or cleaning the filters
HI (Fig. 3B) - The saturation of the grease filter will be indicated by the operation LED. By switch off cooker hood and
To remove the aluminuim grease filter (Fig. 1), grab the opening tongue at the filter, pull it in your direction and move
pushing the bottom T the operation LED will indicate different colours with following meanings:
the filter downwards. To reinstall it operate reversed.
Green Light: less than 6 working hours
What to do in the case of a defect?
Yellow Light: between 6 and 12 working hours
In the case of a service call, please give your service agent the following information:
Red Light: more than 12 working hours (the grease filter should be cleaned or eventual changed)
HR (Fig. 3A) - The saturation of the grease filter will be indicated automatically after 20 hours by means with flashingModel
of the running speed of the cooker hood. That mean the grease filter should be cleaned or eventual changed.Type
It is as well possible to select manual the degree of saturation. By switch off cooker hood and pushing the bottoms 1Manuf.-No.
and 3 temporary for more than 2 seconds:
You will find this information on the type plate, situated next to the ventilation motor. Enter the numbers immediately
- No flashing light of the bottom: less than 6 working hours
into the appropriate boxes. This information will enable the service agent to prepare the necessary spare parts
- Flashing light of bottom 1: between 6 and 12 working hours
in advance, so that your cooker hood can be repaired on the first service visit.
- Flashing light of bottom 1 and 2: between 12 and 18 working hours
Technical data
- Flashing light of bottom 1, 2 and 3: more than 18 working hours
Linking value: motors 1 x 200 W
After you have cleaned or eventual changed the grease filter you should reset the timer by means pushing the main
Lighting: 2 x 20 W
switch for more than 2 seconds. If the Timer will not by reset manual the electronic will reset after 15 minutes
Total value: 240 W / 230 V / 50 Hz
automatically the Timer.
Electric linking: fixed electric cable 0,9 m with safety plug. In case of interventions remove the plug!
If your cooker hood is supplied with a charcoal filter and is running in the filtering method the saturation of the charcoal3
Power: 510 m/h max. |