1 Antenna Receptacle% Right Rear (+) Speaker Output Lead (Violet) (CDA-
2 Power Antenna Lead (Blue)7894/CDA-7893/CDA-7892 only)
Connect this lead to the +B terminal of your power antenna,& Left Rear (+) Speaker Output Lead (Green) (CDA-
if applicable.7894/CDA-7893/CDA-7892 only)
NOTE( Left Rear (�) Speaker Output Lead (Green/Black)
This lead should be used only for controlling the vehicle's power(CDA-7894/CDA-7893/CDA-7892 only)
antenna. Do not use this lead to turn on an amplifier or a signal
) Left Front (�) Speaker Output Lead (White/Black)
processor, etc.
(CDA-7894/CDA-7893/CDA-7892 only)
3 Remote Turn-On Lead (Blue/White)
~ Left Front (+) Speaker Output Lead (White) (CDA-
Connect this lead to the remote turn-on lead of your
7894/CDA-7893/CDA-7892 only)
amplifier or signal processor.
+ Ai-NET Connector
4 Audio Interrupt In Lead (Pink/Black)
Connect this to the output or input connector of other
5 Illumination Lead (Orange)
product (CD Changer, Equalizer, etc.) equipped with Ai-
This lead may be connected to the vehicle's instrumentNET.
cluster illumination lead. This will allow the backlighting of
NOTE
the CDA-7995/CDA-7894/CDA-7893 to dim whenever the
You can input TV/video sound by connecting an optional Ai-
vehicle's lights are turned on.
NET/RCA Interface cable (KCA-121B) to this component.
6 Switched Power Lead (Ignition) (Red)
, DC/DC Converter (CDA-7995/CDA-7894 only)
Connect this lead to an open terminal on the vehicle's fuse
box or another unused power source which provides (+)12VNOTES
only when the ignition is turned on or in the accessory" Do not install the converter at a location subjected to water
such as under the floor mat or air conditioner. This may cause
position.
a malfunction.
7 Battery Lead (Yellow)" Do not bundle the DC/DC converter cable with other audio
Connect this lead to the positive (+) post of the vehicle'scables. Doing so may induce noise into your system.
battery." Keep the DC/DC converter away from the Antenna cables and
the rear side of the unit, otherwise noise may be generated
NOTE (CDA-7894/CDA-7893 only)
when receiving radio broadcast.
Use an extension battery lead (20A)(sold separately) and
connect it directly to the positive (+) side of the vehicle's battery.- Ai-NET Cable (Included with CD Changer)
8 Ground Lead (Black). Front Output RCA Connectors
Connect this lead to a good chassis ground on the vehicle./ Rear Output RCA Connectors
Make sure the connection is made to bare metal and isRED is right and WHITE is left.
securely fastened using the sheet metal screw provided.
: Subwoofer RCA Connectors
9 Fuse HolderRED is right and WHITE is left.
(5A ........ CDA-7995 only)
; RCA Extension Cable (Sold Separately)
(15A ...... CDA-7892 only)
< System Switch
(20A ...... CDA-7894/CDA-7893 only)
When connecting a processor or divider using Ai-NET, place
! Power Supply Connector
this switch in the EQ/DIV position. When no device is
" Right Front (+) Speaker Output Lead (Gray) (CDA-connected, leave the switch in the NORM position.
7894/CDA-7893/CDA-7892 only)
NOTE
# Right Front (�) Speaker Output Lead (Gray/Black)Be sure to turn the power off to the unit before changing the
(CDA-7894/CDA-7893/CDA-7892 only)switch position.
$ Right Rear (�) Speaker Output Lead (Violet/Black)
(CDA-7894/CDA-7893/CDA-7892 only)
To prevent external noise from entering the audio system.
" Locate the unit and route the leads at least 10 cm away from the car harness.
" Keep the battery power leads as far away from other leads as possible.
" Connect the ground lead securely to a bare metal spot (remove any paint, dirt or grease if necessary) of the car chassis.
" If you add an optional noise suppressor, connect it as far away from the unit as possible. Your Alpine dealer carries various noise
suppressors, contact them for further information.
" Your Alpine dealer knows best about noise prevention measures so consult your dealer for further information.
39-EN |
ACEC
