Troubleshooting Guide
Tips and advice Before starting a wash programme,Croc kery still dirty after washing:
Arrange crockery so that items do nomake sure that the spray t arms can tuWrn as the crockery loaded properly?
AFTER-SALES
touch each other. Arrange large freely and are not impeded by crock eCry rockery must be loaded facing
crockery in the lower rack and smallor cuer tlery.downwards; this is important, especially SERVICE
crockery in the upper rack.Only switch off the dishwasher once for large items of crockery.
r carrying out the above checks
Load cups at an angle to facilitateth e ?Star?t indicator lamp has switched The water jets must spray the entIifr aftee
water drainage.off. If the dishwasher is switched offsurfa ce of all items.the malfunction persists or appears
n, turn the appliance off and turn
Generally speaking, place cutlery induring a the wash cycle, when switched on Make sure that crockery and cutlery agaiare
arranged properly.off the water supply tap, then call
basket with the handles positioned again it will resume the cycle from
our After-Sales Service (see guarantee).
downwards, but ensure that any sharwhp ere it was interrupted without ha vinHave g you selected the correct programme?
Please specify:
Did you use too much or too little
knives and forks that might cause to start it a. gainThe nature of the fault.
detergent? (The use of poor quality
injury are placed in the basket with the
detergents may result in less effect Thivee a ppliance type and model.
handles positioned upwards.
washing). The service code (the number after
Make sure the water jet can reach all the word Service on theadhesive
Are the filters clogged or incorrectly
loaded items and that the spray arms rating plate) inside the door
If a fault occurs, before contacting ouassemr bled? (See?C are and
turn freely.After-Sales Service, make the following on the right-hand side.
Maintenance? chapter in the user
Importantchecks to try and remedy the problem:
instructions).
Fill the detergent dispenser and chThe deck ishwasher is not working: Are the spray arms blocked or the nozzles
the salt and rinse aid level. Is the plug properly inserted in thcle waloggeld?
(See ?Care and Maintena?nce
Do not use the appliance for items nosocket?t chapter in the user instructions).
suitable for washing in a dishwash er, Is there a power failure? Is the lower spray arm correctly fitted?Your full address and telephone
for example: wooden items, aluminium, Is the dishwasher switched on?number.
Is the salt container cap (water softening
plastic utensils, tin, hand-decora tHedas t he Start button been pressed?system) screwed down?
crockery (unglazed), silver cutlery.
Has the delayed start timer been setMark (ifed cr ockery:
Do not put liquid fat in the dishwafittesher d)? Is the water hardness level selector not
(e.g. oil used for frying) or candleIs wa thx.e water supply tap on? properly adjusted? ?Fil(Seline g the salt
If a fault occurs or you wish to ch Isan thege flow of water obstructed by containe? ir n the user instructions).
the current programme, press the impurities? If so, close the water suppl Is thy tape sal, t container empty?
?START ? button for about 5 seconds detach the water hose and clean the filter. (See ?Filling the salt co? inntainer
until the Start indicator lamp switcheThen re-cons nect the water hose to thet htape use r instructions).
off.and open the water tap once again. Was insufficient detergent used?
If regeneration salt is to be adde d,Are the filters clogge?Cad? (Sre aneed (See ?Filling the detergent dis? penser
immediatel sty art a wash programme Maintenance? chapter in the user in the user instructions).
in order to eliminate any residual salinstructions).t Marked glasses and cutlery:
(rinsing alone is not sufficient). Is the door closed properly? Was too much rinse aid used?
Sometimes even though the Is a fault indicated? (See ?Filling the rinse aid dis?penser
regeneration salt container has been(The S tart indicator lamp flashes).in the user instructions).
filled, the corresponding indicator Stlaartmp the programme again from the Note: with some models, when the Start
(if fitted) will light up during thbee first ginning: press the Start buttonbutton is pressed a pre-was for h cycle precedes
wash cycle after filling with salt.about 5 seconds, until the Start thine adicactuator l wash programme; this
lamp switches off.regenerates the water softening system.
Select a new programme and press the
Start button.
Please read the user instructions carefully. |
ACEC
