Troubleshooting Guide
Tips and advice Before starting a wash programme, Crockery still dirty after washing:
Arrange crockery so that items do nomake sure thatt the spray arms can t uWarn s the crockery loaded properly?
AFTER-SALES
touch each other. Arrange large freely and are not impeded by crockery Crockery must be loaded facing
crockery in the lower rack and smalor culer tlery.downwards; this is important, especially SERVICE
crockery in the upper rack. Only switch off the dishwasher once tfor large he items of crockery.
Load cups at an angle to facilitate? Star?t indicator lamp has switched off. The water jets must spray the entire If after carrying out the above checks
the malfunction persists or appears
If the dishwasher is switched off during
water drainage.surface of all items.again, turn the appliance off and turn
a wash cycle, when switched on again it
Generally speaking, place cutlery in the Make sure that crockery and cutlery are off the water supply tap, then call our
will resume the cycle from where it was
basket with the handles positioned arranged properly.After-Sales Service (see guarantee).
interrupted without having to start it
downwards, but ensure that any sharp Please specify:
again. Have you selected the correct programme?
knives and forks that might cause The nature of the fault.
Did you use too much or too little
injury are placed in the basket with the
detergent? (The use of poor qualit y The appliance type and model.
handles positioned upwards.
detergents may result in less effective The service code (the number after
Make sure the water jet can reach all If a fault occurs, before contacting ourwashi ng).the word Service on the adhesive
loaded items and that the spray arms After-Sales Service, make the following
rating plate) inside the door on
Are the filters clogged or incorrectly
turn freely.checks to try and remedy the problem:the right-hand side.
assembled? (See ?Care and Maintenance?
ImportantThe dishwasher is not working:
Is the plug properly inserted in thchapter in the ue wall ser instructions).
Fill the detergent dispenser and check
socket? Are the spray arms blocked or the nozzles
the salt and rinse aid level.
Is there a power failure?clogged? (See?Ca re and Maintena?nce
Do not use the appliance for items not chapter in the user instructions).
Is the dishwasher switched on?
suitable for washing in a dishwash er,Has t he Start button been pressed?Is the lower spray arm correctly fitted?Your full address and telephone number.
for example: wooden items, aluminium,
Has the delayed start timer been set (if
Is the salt container cap (water softening
plastic utensils, tin, hand-decorated
fitted)?
crockery (unglazed), silver cutlery.system) screwed down?
Is the water supply tap on?
Do not put liquid fat in the dishwasIs thher e flow of water obstructed by Marked crockery:
(e.g. oil used for frying) or candle impuwaritx.ies? If so, close the water suIs pplthe waty er hardness level selector not
If a fault occurs or you wish to chantage p, detach the water hose and cleanpro thpee rly adjusted? See?Filli (ng the salt
the current programme, press the filter. Then re-connect the water hcoose ntato ine? inr the user instructions).
?START ? button for about 5 seconds until the tap and open the water tap once Is the salt container empty? (See ?Filling the
the Start indicator lamp switches off.again.salt containe? in the user instructions).r
Are the filters clogge?Cad? (Seere and
If regeneration salt is to be added, Was insufficient detergent used? (See
maintenance? chapter in the user
immediatel starty a wash programme ?Filling the detergent di? in spethense r
instructions).
in order to eliminate any residual salt user instructions).
Is the door closed properly?
(rinsing alone is not sufficient).Marked glasses and cutlery:
Is a fault indicated?
Sometimes even though the Was too much rinse aid used? (See
(The Start indicator lamp flashes).
regeneration salt container has been ?Filling the rinse aid di? inspe thne seuser r
Start the programme again from the
filled, the corresponding indicator lamp instructions).
beginning: press the Start button for
(if fitted) will light up during the first
about 5 seconds, until the Start Note:indi withcator some models, when the Start
wash cycle after filling with salt.
lamp switches off.button is pressed a pre-wash cycle precedes
Select a new programme and press tthe ahe ctual wash programme; this
Start button.regenerates the water softening system.
Please read the user instructions carefully. |
ACEC
