Troubleshooting Guide
Tips and advice Before starting a wash programme,
Crockery still dirty after washing:
Arrange crockery so that items do nomake sure thatt the spray arms can turn Was the crockery loaded properly?AFTER-SALES
touch each other. Arrange large freely and are not impeded by crockery
Crockery must be loaded facing
crockery in the lower rack and smalor culer tlery.downwards; this is important, especially SERVICE
crockery in the upper rack. Only switch off the dishwasher once tfor large he items of crockery.
Load cups at an angle to facilitate? Star?t indicator lamp has switched off. The water jets must spray the entire If after carrying out the above checks the
malfunction persists or appears again,
water drainage.If the dishwasher is switched off during surface of all items.
turn the appliance off and turn off the
Generally speaking, place cutlery ina wash cycle, the when switched on again it Make sure that crockery and cutlery are
water supply tap, then call our After-Sales
basket with the handles positioned will resume the cycle from where it was arranged properly.
Service (see guarantee). Please specify:
downwards, but ensure that any sharintp errupted without having to start itHave you sel ected the correct
The nature of the fault.
knives and forks that might cause again.programme?
The appliance type and model.
injury are placed in the basket with the Did you use too much or too little
The service code (the number after the
handles positioned upwards.detergent? (The use of poor quality
word Service on the adhesive rating plate)
Make sure the water jet can reach all detergents may result in less effective inside the door on the right-hand side.
loaded items and that the spray arms If a fault occurs, before contacting ourwashi ng).
turn freely.After-Sales Service, make the followingAre t he filters clogged or incorrectly
checks to try and remedy the problem:
Importantassembled? (See ?Care and
Fill the detergent dispenser and chTheeck dishwasher is not working:Maintenance? chapter in the user
the salt and rinse aid level. Is the plug properly inserted in thinste waructions).ll Your full address and telephone number.
Do not use the appliance for items nosockett ? Are the spray arms blocked or the nozzles
clogged? (See?Ca re and Maintena?nce
suitable for washing in a dishwash er,Is th ere a power failure?
for example: wooden items, aluminium,Is th e dishwasher switched on?chapter in the user instructions).
Is the lower spray arm correctly fitted?
plastic utensils, tin, hand-decora teHad s the Start button been pressed?
crockery (unglazed), silver cutlery. Has the delayed start timer been set Is the salt container cap (water softening
system) screwed down?
Do not put liquid fat in the dishwas(if fitteher d)?
Is the water supply tap on? Marked crockery:
(e.g. oil used for frying) or candle wax.
Is the flow of water obstructed by Is the water hardness level selector not
If a fault occurs or you wish to change
impurities? If so, close the water supproply tap, perly adjusted? See?Filli (ng the salt
the current programme, press the
detach the water hose and clean the ficolter.ntaine ? inr the user instructions).
?START ? button for about 5 seconds,
Then re-connect the water hose to the tap Is the salt container emp?tFiy?lli (Seeng
until the corresponding indicator lamp
and open the water tap once again.the salt cont?ai inne thr e user
lights up.
Are the filters clogge?Cad? (Seere and instructions).
If regeneration salt is to be added,
maintenance? chapter in the user Was insufficient detergent used? (See
immediatel starty a wash programme
instructions).?Filling the detergent di? in spethense r
in order to eliminate any residual salt
Is the door closed properly?user instructions).
(rinsing alone is not sufficient).
Is a fault indicated? Marked glasses and cutlery:
Sometimes even though the (The Start indicator lamp flashes). Was too much rinse aid used? (See
regeneration salt container has been
Start the programme again from the ?Filling the rinse aid di? inspe thne seuser r
filled, the corresponding indicator lamp beginning: press the Start button for instructions).
(if fitted) will light up during the first
about 5 seconds, until the Start Note:indi wicator th some models, when the Start button
wash cycle after filling with salt.
lamp switches off.is pressed a pre-wash cycle precedes the
Select a new programme and press actual wthe ash programme; this regenerates the
Start button.water softening system.
Please read the user instructions carefully. |
ACEC
