Troubleshooting Guide
Tips and advice Before starting a wash programme,Croc kery still dirty after washing:
Arrange crockery so that items do nomake sure that the spray t arms can tuWrn as the crockery loaded properly?
AFTER-SALES
touch each other. Arrange large freely and are not impeded by crockery
Crockery must be loaded facing
crockery in the lower rack and smallor cuer tlery.SERVICE
downwards; this is important, especially
crockery in the upper rack.Switch off the dishwasher once the for large items of crockery.
If after carrying out the above checks
Load cups at an angle to facilitate? Start? indicator lamp has switched off.
The water jets must spray the entthire me alfunction persists or appears
water drainage. If you switch off the dishwasher during
surface of all items.again, turn the appliance off and turn
Generally speaking, place cutlery ina w thae sh cycle, when switched on again
Make sure that crockery and cutlery off the water suare pply tap, then call our
basket with the handles positioned the dishwasher resumes the cycle from
arranged properly.After-Sales Service (see guarantee).
downwards, but ensure that any sharwhp ere it was interrupted without having
Please specify:
Have you selected the correct programme?
knives and forks that might cause to start it a. gain The nature of the fault.
injury are placed in the basket with the Did you use too much or too little detergent?
The appliance type and model.
handles positioned upwards.(The use of poor quality detergents may
The service code (the number after
Make sure the water jet can reach all result in less effective washing).the word Service on the adhesive
If a fault occurs, before contacting our
loaded items and that the spray arms Are the filters clogged or incorrectly rating plate) inside the door
turn freely.After-Sales Service, make the following assembled? (See ?Care and Maintena?nce on the right-hand side.
checks to try and remedy the problem:
Importantchapter in the user instructions).
The dishwasher is not working:
Fill the detergent dispenser and check Are the spray arms blocked or the nozzles
the salt and rinse aid level. Is the plug properly inserted in the wall clogged? (See ?Care and Maintena?nce
socket?
Do not use the appliance for items not chapter in the user instructions).
Is there a power failure?
suitable for washing in a dishwasher, Is the lower spray arm correctly fitted?Your full address and telephone number.
Is the dishwasher switched on?
for example: wooden items, aluminium,
Has the Start button been pressed?Is the salt container cap (water softening
plastic utensils, tin, hand-decorated
Has the delayed start timer been setsys (iftem) screw ed down?
crockery (unglazed), silver cutlery.
fitted)?Marked crockery:
Do not put liquid fat in the dishwasher
Is the water supply tap on?
(e.g. oil used for frying) or candle wax. Is the water hardness level selector not
Is the flow of water obstructed by properly adjusted? Se?File (ling the salt
If a fault occurs or you wish to change
impurities? If so, close the water supply tap,
the current programme, press the containe? ir n the user instructions).
detach the water hose and clean the filter.
?START ? button for about 5 seconds until Is the salt container empty? (See ?Filling the
Then re-connect the water hose to the tap
the Start indicator lamp switches off.salt contai? inern the user instructions).
and open the water tap once again.
If regeneration salt is to be adde d,Are the filters clogge?Cad? (Sre aneed Was insufficient detergent used? (See
immediatel sty art a wash programme ?Filling the detergent di? inspe thnsee r
Maintenance? chapter in the user
in order to eliminate any residual salt instructions).user instructions).
(rinsing alone is not sufficient).
Is the door closed properly?Marked glasses and cutlery:
Sometimes even though the Is a fault indicated? Was too much rinse aid used? (See
regeneration salt container has been(The S tart indicator lamp flashes).
?Filling the rinse aid di? inspe thne useser r
filled, the corresponding indicator Stlaartmp the programme again from the instructions).
(if fitted) will light up during thbee first ginning: press the Start button for
Note: with some models, when the Start button
wash cycle after filling with salt.about 5 seconds, until the Start indicator
is pressed a pre-wash cycle precedes the
lamp switches off.
actual wash programme; this regenerates the
Select a new programme and press the
water softening system.
Start button.
Please read the user instructions carefully. |
ACEC
