B100 TWOTWOTWO CHANNELCHANNEL POWER POWER AMPLIFIERAMPLIFIER
labeled AUX1/PHONOAUX1/PHONOAUX1/PHONO accept accept moving moving magnet magnet phono phono cartridge cartridge inputs. These inputs. inputs are These NOT line inputs level are NOT line level
inputs in the B100-P and cannot be used as such.
LINE LEVEL ANALOG AUDIO OUTPUTS :The Bryston B100 integrated amplifier comes equipped
with 2 pairs of gold plated analog RCA jacks PREAMPPREAMPPREAMPfor outputs:OUTOUTOUT and and RECORD RECORD RECORD OUTOUTOUT . .
? PREAMPPREAMPPREAMP OUTOUTOUT is is normally normally connected, connected, internally, internallyvia the CONNECTED/SEPCONNECTED/SEPCONNECTED/SEP, via the ARAARAARATETETE switch, switch, to POWER to
AMP IN
? RECORD RECORD RECORD OUTOUTOUT output output is not is afnot fected afby fected volume, by balance volume, or mute balance controls.or mute controls.
DIGITAL AUDIO INPUTS:In the B100-DA model, which contains a stereo D/A converter module,
there are 4 digital audio inputs available.
Two TOSLINK optical inputs are selected by TVTVTVpressing (T(TOSLINK-1) OSLINK-1) the or or VIDEOVIDEOVIDEO (T(TOSLINK-2) OSLINK-2) buttons buttons on on
the front panel (when in digital mode) or, on the handheld DIGITDIGITDIGITremote, AL-TVAL-TVAL-TV by or or DIGITpressing AL-VIDEO
buttons.
Two SPDIF coaxial inputs can be connected to the B100-DA using the RCA AUX-2/SPDIF-input jacks labeled
1 and AUX-2/SPDIF-2. To select these inputs first place the unit in digital ANALOG/mode by pressing the
DIGITAL button on the front panel A/D (or button the on the handheld remote) and then CDCDCD press or or TUNERthe
button on the front DIGITDIGITDIGITpanel AL-CDAL-CDAL-CD( or or DIGITDIGITDIGITAL-TUNERAL-TUNERAL-TUNER on on the the remote). remote). When When the green the LED green above LED the above the
font panel ANALOG/DIGITAL switch in ON concurrently with CDeither , TVTVTV, , TUNER the or VIDEO LEDs, then
digital mode is engaged. When the LED is OFF the B100-DA is in analog mode and the two SPDIF input jacks
now function as analog line level audio AUXAUXAUX--2). inputs (
See the DIGITDIGITDIGITAL-to-ANALOG AL-to-ANALOG AL-to-ANALOG CONVERTER CONVERTER CONVERTER OPTIONOPTIONOPTION section section for more for information. more information.
HEADPHONE JACK:There is a quarter inch headphone output jack available on the front panel of the
Bryston B-100 integrated amplifier. The headphone output is driven directly from the preamplifier section uti-
lizing separate headphone buffers. Inserting the headphone jack mutes the loudspeakers automatically (indi-
cated by the mute LED on the front panel turning PREAMPPREAMPPREAMPred). OUTOUTOUTThe is B100 is also also muted.muted.
You can adjust the volume setting of the headphones by using the volume control on the front of the B-100
integrated amplifier. You may also utilize the remote control unit to adjust headphone volume. The headphones
cannot be muted with the remote control unit or the front panel Mute. Only headphones with impedances of
greater than 50 ohms should be used.
AUXILIARY IR INPUT:This mono 1/8 (3mm) phone jack allows a direct connection to equipment whose
remote control system provides an output from their infra-red LED drive circuit. The signal connected to this jack
should be 1.8Vdc and 9Vdc. tip of The the phone jack is positive ringringring(+) is is negative and negative the (-).(-).
LLLEEEDDD SSSTTTAAATTTUUUSSS ININDICATORS:
CLIPPING: This LED (light emitting diode) will flash RED when the output waveform is clipped thus
indicating an overload condition.
MUTE: Lights GREEN to indicate the outputs are muted..
POWER : GREEN indicates normal operation
RED indicates Standby
Blinking RED/GREEN a fault or thermal overload problem in the unit.
ANALOG/DIGITAL : In B100-DA models: when this LED is illuminated green concurrently with either
CD, TUNER , TV or VIDEO LEDs, it indicates that the digital SPDIFSPDIFSPDIF--1, inputs
SPDIF-2, TOSLINK-1 or TTTOSLINK-2OSLINK-2OSLINK-2 (respectively) (respectively) have been have selected. been selected.
In B100 & B100-P models: when illuminated green this LED indicates that the line level
analog audio input AUX-2AUX-2AUX-2 has has been been selected.selected.
AUX1, CD, TUNER, TV/SAT VIDEO & RECORD:One of these input source LEDs will light green to
indicate the active input. In digital mode these LEDs bit will stream light is RED if the
2 |
ACEC
