B100B100B100 TWO TWO CHANNELCHANNEL POWER POWER AMPLIFIERAMPLIFIER
WIRED RS232 REMOTE CONTROL:
Using the DB9-female connector at the rear of the unit, the B100 can receive commands via a null modem cable at
9600 baud, 8 data bits, no parity and 1 stop bit (9600,8,N,1). Valid commands will return the 3>´ character indicating
that the unit is ready to receive a new command. An invalid command will return the 3!´ character. These serial data
commands are as follows:
000 - power off015 - power on/off toggle081 - select digital source CD)1 (
001 - select analog source A/D) 1 ( 019 - balance left082 - select digital source TUNER) 2 (
002 - select analog source (AUX/PH)2 020 - balance right083 - select digital source TV)3 (
003 - select analog source (CD) 3 029 - power on084 - select digital source VIDEO) 4 (
004 - select analog source (TUNER)4 058 - mute on245 - set/reset Pass Through mode
005 - select analog source (TV) 5 059 - mute off247 - Set TTTrigger rigger rigger for for 222 current current sourcesource
006 - select analog source (VIDEO)6 061 - record monitor toggle248 - CleTTTarrrriii ggggggeeerrr fof222ro cru rcreunrtr seonutrc esource
007 - volume up062 - record monitor on255 - System reset; restore defaults
008 - volume down063 - record monitor off
DIGITDIGITAL-to-ANAL-to-ANALALOG OG (D/A) (D/A) CONVERCONVERTER TER OPTION: OPTION:
The B100-DA comes equipped with stereo Digital-to-Analog converter (D/A or DAC) module. This module is
also retrofittable to standard B100 units.
A unique feature of the B100-DA is its ability to utilize up to four independent digital sources (two SPDIF and
two TOSLINK). These four digital inputs can be accessed CDCDCD, , TUNERTUNERTUNERby selecting , , TV and VIDEO sources
with the DAC feature enabled (by pressing the Analog/Digital button on the left side of the front panel).
Activate the DAC feature by pressing the ANALOG/DIGITAL button on the left side of the front panel (or A/D
on the remote). The LED over ANALOG/DIGITthe AL button will turn Green. Pressing any of the following
four buttons will cause their LEDs to light green, as well, to indicate a PCM digital source is present and con-
nected properly.
? SPDIF 1 is accessed by selecting CD on the front panel DIGITDIGITDIGITor AL-CDAL-CDAL-CD on on the the remote. remote.
? SPDIF 2 is accessed by selecting TUNER on the front panel DIGITDIGITDIGITor AL-TUNERAL-TUNERAL-TUNER on on the the remote. remote.
? Optical 1 is accessed by selecting TVTVTV on on the the front front panel or panel DIGITDIGITDIGITor AL-TVAL-TVAL-TV on on the the remote.remote.
? Optical 2 is accessed by selecting VIDEOVIDEOVIDEO on on the the front front panel or panel DIGITDIGITDIGITor AL-VIDEOAL-VIDEOAL-VIDEO on on the the remote. remote.
The source LEDs will turn GREEN when a PCM digital bit stream is present. If there is no bit stream available
or an incorrect bit stream (NON-PCM) the LED will turn RED.
You may re-select Analog by simply depressing ANALOG/DIGITthe AL button once more and the LED will
extinguish.
All of the above functions are available from the hand held remote control as well .
MOVING-MAGNET PHONO STAGE OPTION:
The B100-P containmoving s a magnet phono stage. The Phono Stage is modular and can be added to the stan-
dard B100 model later if required by your Bryston dealer.
Bryston?s MM Phono section features state-of-the-art accuracy in equalization, extremely low noise and distor-
tion, and provides headroom margins sufficient to prevent overload from any known phono source. To access the
Phono section simply plug your left/right turntable interconnecAUX-1/PHONOAUX-1/PHONOAUX-1/PHONOt leads into i niptnuhptesu tolsne fotn/ right
the rear panel of the B100 andAUX-1/PHONO press the button on the front paAUX-1/PHONOAUX-1/PHONOAUX-1/PHONOnel. The LLEEDD wwilil ll
turn greeInf. your turntable provides a separate ground lead, system noise may be minimized by connecting it to
the ground lug in the center of the rear panel.
4 |
ACEC
