2358-2
4.When the character you want is at the cursor position, press C to move the cursorALARM
to the right.
5.Repeat steps 3 and 4 until the name is complete.Hourly time signal on You can set a Daily Alarm. When an alarm is turned on,
"You can input up to eight characters for the name.indicatorthe alarm tone sounds when the alarm time is reached.
6.After you input the name, press C as many times as necessary to move the cursorYou can also turn on an Hourly Time Signal that causesTimekeeping Mode time
to the number area.the watch to beep twice every hour on the hour.
"You can input up to eight characters for the name. When the cursor is located at"The alarm and Hourly Time Signal operate in
the eighth space of the name, moving the cursor to the right causes it to jump toaccordance with the current digital time (Timekeeping
the first digit of the number. When the cursor is at the 12th digit of the number,Mode time).
moving it to the right (by pressing C) causes it to jump to the first character in the"All of the operations in this section are performed in the
name.Alarm Mode, which you enter by pressing C.
7.Use B and D to change the character (hyphen, number, or space) at the cursor
position in the number area. The character changes in the following sequence.
Press .
to (space)Alarm time
Press .Alarm on indicator
8.When the character you want is at the cursor position, press C to move the cursorTo set the alarm time
to the right.1.In the Alarm Mode, hold down A until the hour digits of
9.Repeat steps 7 and 8 until you complete number input.the alarm time start to flash.
"You can input up to 12 digits for the number."This automatically turns on the alarm.
"The number initially contains all hyphens. You can leave the hyphens or replace2.Press C to move the flashing between the hour and
them with numbers or spaces.minutes.
10. Press A to store your data and return to the Telememo record screen (without3.While a setting is flashing, use D(+) to change it.
the cursor)."When setting the alarm time using the 12-hour format,
"When you press A to store data, the message may appear on the displaytake care to set the time correctly as a.m. (no
for a while, indicating that data is being sorted. After the sort operation isindicator) or p.m. (P indicator).
complete, the Telememo record screen appears.4.Press A to return to the alarm display screen.
To recall Telememo recordsDaily Alarm Operation
In the Telememo Mode, use D(+) and B(�) to scroll through Telememo records onThe alarm sounds at the preset time each day for about 20 seconds, or until you stop
the display.it by pressing any button.
"The alarm and hourly time signal sound in all modes.
To edit a Telememo record
1.In the Telememo Mode, scroll through the records and display the one you want toTo test the alarm
edit.In the Alarm Mode, hold down D to sound the alarm.
2.Hold down A until the flashing cursor appears on the display.
3.Use C to move the flashing to the character you want to change.To turn the Daily Alarm and Hourly Time Signal on and off
4.Use B and D to change the character.In the Alarm Mode, press B to cycle through the on and off settings as shown below.
"For details on inputting characters, see OTo create a new Telememo record� (step
3 for name input and 7 for number input).Alarm On Indicator/Hourly Time Signal On Indicator
5.After making the changes that you want, press A to store them and return to the
Telememo record screen.
To delete a Telememo recordAlarm OnAlarm OffAlarm OnAlarm Off
1.In the Telememo Mode, scroll through the records and display the one you want toSignal OnSignal OffSignal OffSignal On
delete.
2.Hold down A until the flashing cursor appears on the display.
3.Press B and D at the same time to delete the record.
"The message appears to indicate that the record is being deleted. After the
record is deleted, the cursor appears on the display, ready for input.STOPWATCH
4.Input data or press A to return to the Telememo record screen.
1/100 secondThe stopwatch lets you measure elapsed time, split times,
and two finishes.
"The display range of the stopwatch is 23 hours, 59
minutes, 59.99 seconds.
WORLD TIME"The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
GMT differentialWorld Time shows the current time in 27 cities (29 time"The stopwatch measurement operation continues even
zones) around the world.if you exit the Stopwatch Mode.
World map"For full information on city codes, see the OCITY CODE"All of the operations in this section are performed in the
TABLE�.Stopwatch Mode, which you enter by pressing C.
"The time zone that corresponds to the selected cityHoursSeconds"The time on the screen may not appear to stop
code flashes on the world map.immediately when you press the button to stop an
"All of the operations in this section are performed in theMinuteselapsed time operation or perform a split time operation
World Time Mode, which you enter by pressing C.in the Stopwatch Mode. Despite this, the time recorded
by your button operation is accurate.
To view the time in another city code
While in the World Time Mode, press D to scroll forwardTo measure times with the stopwatch
through the city codes (time zones) and B to scroll back.Elapsed Time
"If the current time shown for a city is wrong, check your
Timekeeping Mode time and Home City code settings
City code
and make the necessary changes.StartStopRe-startStopClear
Current time in the
selected city code
Split Time
To toggle a city code time between standard time and Daylight Saving Time
1.In the World Time Mode, use B and D to display the
city code (time zone) whose standard time/DaylightStartSplitSplit releaseStopClear
Saving Time setting you want to change.
2.Hold down A for about two seconds to toggle DaylightTwo Finishes
Saving Time (DST displayed) and standard time (DST
not displayed).
"The DST indicator is on the display whenever youStartSplitStopSplit releaseClear
display a city code for which Daylight Saving Time isFirst runner Second runner Record time of
turned on.finishes.finishes.second runner.
"Note that the DST/Standard Time setting affects onlyRecord time of
the currently displayed city code. Other city codes arefirst runner.
not affected.
"Note that you cannot switch between standard time
and Daylight Saving Time while is selected as
the city code. |