MA0310-EA
Operation Guide 3321
About This Manual
" Button operations are indicated using the letters shown
in the illustration.
" Each section of this manual provides you with the
information you need to perform operations in each
mode. Further details and technical information can be
found in the OReference� section.
General Guide
" Press B to change from mode to mode.
Timekeeping ModeCalendar ModeAlarm ModeDual Time ModeStopwatch Mode
Press .
TimekeepingAlarm
Use this mode to set the current time. An incorrect digital time setting will causeWhen the Daily Alarm is turned on, an alarm sounds for 20 seconds at the preset time
incorrect operation of the calendar.each day. When the Hourly Time Signal is turned on, the watch beeps every hour on
To set the digital timethe hour.
" You can configure alarm settings and Hourly Time Signal settings in the Alarm
Mode, which you enter by pressing B.
Hour hand Minute hand
To set the alarm time and to turn the Daily Alarm and Hourly Time Signal on
and off
Hold down .Press .Press .
SecondsHourAlarm on indicator
Mode indicator
PM
indicator 12/24Minutes
Press .Press .
Hour Seconds
Minutes Hold down Press Press
. .Left .Right
1. In the Timekeeping Mode, hold down C until the seconds digits start to flash,Hourminutesminutes
which indicates the setting screen.digitdigit
Press
2. Press B to reset the seconds to 00. .
3. Press C to move the selection to the hour digits.Alarm/Hourly Time Signal setting
4. Press B to increase the hour digits.HourPress .
5. Press C to move the selection to the minutes digits.Hourly time
6. Press B to increase the minutes digits.Minutes signal on indicator
7. Press C to move the selection to 12/24.1. In the Alarm Mode, hold down C until the hour digits start to flash, which indicates
8. Press B to toggle the timekeeping format between 12-hour and 24-hour.the setting screen.
9. Press C to exit the setting screen.2. Press B to increase the hour digits.
" Resetting the seconds to 00 while the current count is in the range of 30 to 59" The 12/24-hour format of the alarm time matches the format you select for normal
causes the minutes to be increased by 1. In the range of 00 to 29, the seconds aretimekeeping.
reset to 00 without changing the minutes.3. Press C to move the selection to the left minutes digit.
" With the 12-hour format, the P (PM) indicator appears on the display for times in the4. Press B to increase the left minutes digit.
range of noon to 11:59 p.m. and no indicator appears for times in the range of5. Press C to move the selection to the right minutes digit.
midnight to 11:59 a.m.6. Press B to increase the right minutes digit.
" With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without7. Press C to move to the Daily Alarm and Hourly Time Signal on and off setting.
any indicator.8. Press B to cycle through the Daily Alarm and Hourly Time Signal settings as
shown in the sequence below.
To set the hands" At this time Daily Alarm and Hourly Time Signal automatically turn on.
In any mode, press A with a thin object to advance the analog time setting. Each
press of A advances the time by 20 seconds. Three presses advance by one minute.PressPressPress
Holding down A advances the analog setting at high speed. You can only advance . . .
the setting. You cannot reverse it.
Both ONBoth OFFDaily Alarm Hourly Time
onlySignal only
Calendar
Press .
Use this mode to set todayOs date (month, day, day of the week).
9. Press C to exit the setting screen.
To set the date
To stop the alarm
Press any button to stop the alarm after it starts to sound.
To test the alarm and select an alarm tone
Hold down B in any mode (except when making any settings) to sound the alarm.
Hold down .Press .Press .
Note that the alarm sound changes each time you hold down B to test the alarm.
MonthDayDay of weekThere are a total of four different alarm sounds. The last alarm sound you hear when
performing the above test is the one that is used for the Daily Alarm and the Hourly
Time Signal.
Press .
MonthDay of week" Note that holding down B also changes the mode.
Day
1. In the Calendar Mode, hold down C until the month digits start to flash, which
indicates the setting screen.
2. Press B to increase the month digits.
3. Press C to move the selection to the day digits.
4. Press B to increase the day digits.
5. Press C to move the selection to the day of the week.
6. Press B to advance to the next day.
7. Press C to exit the setting screen.
" The watch does not make any allowance for leap years. Be sure to manually set
February 29 when one occurs during a leap year.
1 |
ACEC
