USEROS GUIDE 2705
General Guide
? Some models have a white-on-black display.
? Press A to change from mode to mode.
Timekeeping ModeCalendar ModeAlarm ModeDual Time ModeStopwatch Mode
Press A.
[ Modules 2337/2338 ]
About the Backlight
?Press L to illuminate the display for about 2 seconds.1.Hold down C until the month digits start to flash.
?The backlight of this watch employs an electro-luminescent (EL) light, which2.Press A to increase the month digits. Holding down A changes the digits
loses its illuminating power after very long term use.at high speed.
?Frequent use of the backlight shortens the battery life.3.Press C to move the selection to day digits.
?The watch may emit an audible sound whenever the display is illuminated.4.Press A to increase the day digits. Holding down A changes the digits at
This does not indicate malfunction of the watch.high speed.
?The illumination provided by the backlight may be hard to see when viewed5.Press C to move the selection to the day of the week indication.
under direct sunlight.6.Press A to advance to the next day. Holding down A changes the
?The backlight automatically turns off whenever an alarm sounds.indication at high speed.
?When the backlight is turned on, it blinks whenever the minute hand moves.7.Press C to complete the procedure.
This is normal, and does not indicate malfunction of the watch.? If you do not operate any button for a few minutes while a selection is
?The backlight of Module 2338 illuminates both the digital display and analogflashing, the flashing stops and the watch goes back to the Calendar Mode
face. The backlight of Module 2337 illuminates the digital display only. Theautomatically.
backlight of Modules 2374, 2384 and 2705 illuminates the analog face only.
Alarm Mode
Timekeeping Mode
When the Daily Alarm is turned on, an alarm sounds for 20 seconds at the
? Use this mode to set the current time. An incorrect digital time setting willpreset time each day. When the Hourly Time Signal is switched on, the watch
result in incorrect operation of the calendar.beeps every hour on the hour.
To set the time and dateTo set the alarm time and to turn the Daily Alarm and Hourly Time Signal on
and off
Hour hand Minute hand
Alarm on indicator
Hourly Time Signal on indicator
Hold downPressPress
C.C.Left C.Right
Hold down C.Press C.Press C.Hourminutes minutes
digitdigit
SecondsHour
Press C.Press C.
Alarm/Hourly Time Signal setting
12/24Minutes
Press C.
HourMinutesPress C.Hour Minutes
PM indicatorSeconds1.Hold down C until the hour digits start to flash.
1.Hold down C until the seconds digits start to flash.2.Press A to increase the hour digits. Holding down A changes the digits at
2.Press A to reset the seconds to 00. If you press A while the secondshigh speed.
count is in the range of 30 to 59, the seconds are reset to 00 and 1 is added? The format (12-hour and 24-hour) of the alarm time matches the format you
to the minutes. If the seconds count is in the range of 00 to 29, the minutesselect for normal timekeeping.
count is unchanged.3.Press C to move the selection to the left minutes digit.
3.Press C to move the selection to the hour digits.4.Press A to increase the left minutes digit. Holding down A changes the
4.Press A to increase the hour digits. Holding down A changes the hourdigit at high speed.
digits at high speed.5.Press C to move the selection to the right minutes digit.
5.Press C to move the selection to the minutes digits.6.Press A to increase the right minutes digit. Holding down A changes the
6.Press A to increase the minutes digits. Holding down A changes thedigit at high speed.
minutes digits at high speed.7.Press C to move Daily Alarm and Hourly Time Signal on and off setting.
7.Press C to move the selection to 12/24.8.Press A to change the status of the Daily Alarm and Hourly Time Signal in
8.Press A to toggle the timekeeping format between 12-hour and 24-hour.the following sequence.
? When 12-hour format is selected, the indicator P appears on the display to? At this time Daily Alarm and Hourly Time Signal automatically turn on.
indicate Op.m.� times. There is no indicator for Oa.m.� times.
9.Press C to complete the procedure.[Modules
? If you do not operate any button for a few minutes while a selection is2337/2338]Press
flashing, the flashing stops and the watch goes back to the TimekeepingA.
Mode automatically.[Module 2374]
To set the hands
When in any Mode, press B with a thin object to advance the analog time[Modules 2384/2705]
setting. Each press of B advances the time by 20 seconds. Three presses
advance by one minute.Both ONBoth OFFDaily AlarmHourly Time
Holding down B advances the analog setting at high speed. You can onlyonlySignal only
advance the setting and cannot reverse it.
9.Press C to complete the procedure.
? If you do not operate any button for a few minutes while a selection is
Calendar Modeflashing, the flashing stops and the watch goes back to the Alarm Mode
automatically.
To set the dateTo stop the alarm
? Press any button to stop the alarm after it starts to sound.
To test the alarm and select an alarm tone
Hold down A in any mode (except when making any settings) to sound the
alarm.
Each time you test the alarm, a four different alarm tones. The alarm tone you
Hold down C.Press C.Press C.select is used for the Daily Alarm and Hourly Time Signal.
MonthDayDay of week? Note that holding down A also changes the mode.
Press C.
MonthDay
Day of week
1 |