MA0309-EB
Operation Guide 2790
Getting Acquainted
Congratulations upon your selection of this CASIO watch. To get the most out of your
purchase, be sure to carefully read this manual and keep it on hand for later reference
when necessary.
Expose the watch to bright light to charge its battery before using it.
You can use this watch even as its battery is being charged by exposure to bright
light.
" Be sure to read OBattery� for important information you need to know when
exposing the watch to bright light.
If the digital display of the watch is blank...
If the Power Saving on indicator (PS) is on the display
(either flashing or not flashing), it means that the
display is blank because the watchOs Power Saving
function has turned off the display to conserve
power. Power Saving automatically turns off the display
and enters a sleep state whenever your watch is left for
a certain period where it is dark. If the watch is kept in
the dark for a longer period, the analog hands will also
stop moving after a few days.
" The initial factory default setting is Power Saving on.
" The watch recovers from the sleep state if you move it
to a well-lit area, if you press any button, or if you
angle the watch towards your face for reading.
" See OPower Saving Function� for more
information.
About This Manual
" Button operations are indicated using the letters shown
in the illustration.
" For the sake of simplicity, the sample displays in this
manual do not show the analog hands of the watch.
" Each section of this manual provides you with the
information you need to perform operations in each
mode. Further details and technical information can be
found in the OReference� section.
General Guide
" Press B to change from mode to mode.
" In any mode, press L to illuminate the display.
Timekeeping ModeAlarm ModeStopwatch ModeDual Time ModeHand Setting Mode
Press .
Timekeeping
3. When the setting you want to change is flashing, use C and L to change it as
This watch features both digital and analog timekeeping. Changing the digital timedescribed below.
setting causes the analog setting to be adjusted automatically to match the digital time.ScreenTo do this:Do this:
" Whenever you need to adjust both the digital and the analog time settings, make
36Reset the seconds to 00Press C.
sure you adjust the digital setting first.
" In the Timekeeping Mode, press A to toggle the display between the date screenToggle illumination duration between three secondsPress L.
and the time screen.(3" displayed) and one second (3" not displayed)
P10:08Change the hour or minutesPress C (+).
Date ScreenTime Screen2003Change the year
Minute hand 6-30Change the month or day
Hour : Minutes
4. Press A to exit the setting screen.
Hour hand Press ." When you use the above procedure to set the digital display time, the hands of theanalog timepiece normally adjust according to your setting.
Month - Day " For more information about illumination duration, see ODisplay Illumination�.
" Resetting the seconds to 00 while the current count is in the range of 30 to 59
PM indicator causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are
Seconds 00
Day of week Seconds reset to without changing the minutes.
" The day of the week is automatically displayed in accordance with the date (year,
month, and day) settings.
Digital Time and Date" The year can be set in the range of 2000 to 2099.
Use the Timekeeping Mode to set and view a digital display of the current time and" The watchOs built-in full automatic calendar makes allowances for different month
date. When setting the digital time, you can also specify the illumination duration.lengths and leap years. Once you set the date, there should be no reason to change
it except after you have the watchOs battery replaced.
To set the digital time and date
1.In the Timekeeping Mode, hold down A until theTo toggle between 12-hour and 24-hour timekeeping
seconds start to flash, which indicates the settingIn the Timekeeping Mode, press C to toggle between 12-hour timekeeping (indicated
screen.by A or P on the display), or 24-hour timekeeping.
" The hour hand and minute hand of the watch do not" With the 12-hour format, the P (PM) indicator appears on the display for times in the
move while the setting screen is on the display.range of noon to 11:59 p.m. and the A (AM) indicator appears for times in the range
2.Press B to move the flashing in the sequence shownof midnight to 11:59 a.m.
below to select the other settings." With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
any indicator.
" The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
Seconds/Illumination durationHourMinutes
applied in all modes.
DayMonthYear
1 |
ACEC
