MA0411-EA
Operation Guide 2951
About This Manual
" Button operations are indicated using the letters shown
in the illustration.
" Each section of this manual provides you with the
information you need to perform operations in each
mode. Further details and technical information can be
found in the OReference� section.
General Guide
" Press C to change from mode to mode.
" In any mode, press B to illuminate the display.
Timekeeping e-DATA MEMORY World Time City Temperature Alarm Countdown Timer Stopwatch
ModeModeModeModeModeModeMode
Press .
TimekeepingDaylight Saving Time (DST)
Daylight Saving Time (summer time) advances the time setting by one hour from Standard
Use the Timekeeping Mode to set and view the current time and date.Time. Remember that not all countries or even local areas use Daylight Saving Time.
" Pressing D in the Timekeeping Mode cycles through available screen formats as
shown below.To toggle the Timekeeping Mode time between DST and Standard Time
1.In the Timekeeping Mode, hold down A until the
Day of the Week ScreenMonth - Day ScreenWorld Time Screen
seconds start to flash, which indicates the setting
PM indicator World Time Mode time screen.
Day of week Month . Day (Hour : Minutes) 2.Press C to display the DST setting screen.
Press .
3.Press D to toggle between Daylight Saving Time (ON)
and Standard Time (OFF).
4.Press A to exit the setting screen.
" The DST indicator appears on the display to indicate
that Daylight Saving Time is turned on.
DST indicator
Hour : Minutes Seconds
e-DATA MEMORY
You can use the watchOs e-DATA MEMORY to store e-mail
Text
Read this before you set the time and date !addresses, Web page URLs, and other text data.
The times displayed in the Timekeeping Mode and World Time Mode are linked." All of the operations in this section are performed in the
Because of this, make sure you select a city code for your Home City (the city wheree-DATA MEMORY Mode, which you enter by pressing
you normally use the watch) before you set the time and date.C.
To set the time and datee-DATA MEMORY Management
1.In the Timekeeping Mode, hold down A until thee-DATA MEMORY can hold up to 315 characters total,
seconds start to flash, which indicates the settingwhile each record can contain up to 63 characters. The
screen.maximum number of records depends on the number of
2.Press C to move the flashing in the sequence shownRecord number (Page number) characters per record, as shown below.
below to select other settings." 63 characters per record: 5 records
" 7 or fewer characters per record: 40 records
SecondsDSTCity CodeHourTo create a new e-DATA MEMORY record
1.In the e-DATA MEMORY Mode, press D and B at the
Minutessame time to display the remaining memory screen.
DayMonthYear12/24-Hour 0
Format" If % is shown for remaining memory, it means that
memory is full. To store another record, you will first
3. When the setting you want to change is flashing, use D and B to change it ashave to delete some of the records stored in memory.
described below.2.Hold down A until the flashing cursor (#) appears on
the display, which indicates the setting screen.
ScreenTo do this:Do this:" The setting screen also shows the record number that
Remaining memory (%)
56Reset the seconds to 00Press D.is automatically assigned to the new record.
3.Input the text you want.
OFFToggle between Daylight Saving Time (ON)Press D." When inputting the text, use D (+) and B (�) to
and Standard Time (OFF)
cycle through characters at the current cursor
TYOChange the city codeUse D (east) and B (west).location, and C to move the cursor to the right. See
P10:58Change the hour or minutesUse D (+) and B (�).OInputting Text�.
Toggle between 12-hour (12H) and 24-hourPress D.
12H(24H) timekeeping
2005Change the yearUse D (+) and B (�).4. Press A to store your data and return to the e-DATA MEMORY record screen
(without the cursor).
6-30Change the month or day" Pressing A causes the message SET to appear for about two seconds as the data
is stored. After that, the e-DATA MEMORY record screen appears.
" For full information on city codes, see the OCity Code Table�.
" See ODaylight Saving Time (DST)� for details about the DST setting." The text can show only three characters at a time, so longer text scrolls continuously
from right to left. The last character is indicated by the symbol s after it. Press A to
4. Press A to exit the setting screen.
stop and restart scrolling.
" With the 12-hour format, the P (PM) indicator appears on the display for times in the
range of noon to 11:59 p.m. and the A (AM) indicator appears for times in the range" Records are stored in memory in the sequence they are created.
of midnight to 11:59 a.m.
To recall e-DATA MEMORY records
" With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
any indicator.In the e-DATA MEMORY Mode, press D to cycle through e-DATA MEMORY records
as shown below.
" The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all modes.Press .
" The day of the week is automatically displayed in accordance with the date (year,
month, and day) settings.Remaining
Record 1Record 2memory
()()
screen
1 |
ACEC
