MO0302-A
USEROS GUIDE 2615
Getting Acquainted
Congratulations upon your selection of this CASIO watch. To get the most out of yourAbout This Manual
purchase, be sure to carefully read this manual and keep it on hand for later reference" Button operations are indicated using the letters shown
when necessary.in the illustration.
" Each section of this manual provides you with the
Expose the watch to bright light to charge its battery before using it.information you need to perform operations in each
You can use this watch even as its battery is being charged by exposure to brightmode. Further details and technical information can be
light.found in the OReference� section.
" Be sure to read OBattery� of this manual for important information you need
to know when exposing the watch to bright light.
If the display of the watch is blank...
If the P.SAVE indicator is flashing on the display, it means(Light)
that the display is blank because the watchOs Power
Saving function has turned off the display to conserve
power. Power Saving automatically turns off the display
and enters a sleep state whenever your watch is left for a
certain period where it is dark.
" The initial factory default setting is Power Saving on.
" The watch recovers from the sleep state if you move it to
a well-lit area, if you press any button, or if you angle the
watch towards your face for reading.
" See OPower Saving Function� for more information.
General Guide
" Press C to change from mode to mode.Telememo ModeWorld Time Mode
" In any mode, press L to illuminate the display.
Timekeeping Mode
Press C.
Stopwatch ModeAlarm ModeCountdown Timer Mode
H
Timekeeping
To create a new Telememo record
Use the Timekeeping Mode to set and view the current1.In the Telememo Mode, use B and D to cycle through
Number area
Month � Daytime and date.the record screens until the new data screen appears.
" The new data screen is the one that is blank (contains
Hour : MinutesTo set the time and dateno name and telephone number).
1.In the Timekeeping Mode, hold down A until the" If the message FULL appears on the display, it
seconds start to flash, which indicates the settingmeans that memory is full. To store another record,
screen.you will first have to delete some of the records stored
2.Press C to move the flashing in the sequence shownin memory.
below to select other settings.
Name area
2.Hold down A until the flashing cursor (_) appears in
New Data Screenthe name area of the display.
12/24-Hour Format
SecondsSecondsDSTHourMinutes3.In the name area, use D and B to cycle throughcharacters at the cursor position. The characters cycle
Day of weekin the sequence shown below.
PM indicatorPower SavingDayMonthYear
3. When the setting you want to change is flashing, use D and B to change it asPress D.
described below.
(space)
SettingScreenButton OperationA to Z0 to 9-.:/
SecondsPress D to reset to 00.Press B.
Hour, MinutesUse D (+) and B (�) to change the setting.4. When the character you want is at the cursor position, press C to move the cursor
to the right.
DSTPress D to toggle between Daylight Saving
5. Repeat steps 3 and 4 until the name is complete.
Time (ON) and Standard Time (OF).
" You can input up to eight characters for the name.
12/24-HourPress D to toggle between 12-hour (12H) and6. After you input the name, press C as many times as necessary to move the cursor
Format24-hour (24H) timekeeping.to the number area.
" When the cursor is located at the eighth space of the name area, moving the
Year, Month, DayUse D (+) and B (�) to change the setting.cursor to the right causes it to jump to the first digit of the number. When the
Power SavingPress D to toggle Power Saving on (ON) andcursor is at the 12th digit of the number, moving it to the right (by pressing C)
off (OF).causes it to jump to the first character in the name.
7. In the number area, use D and B to cycle through numbers and symbols
4. Press A to exit the setting screen.(hyphen, space) at the cursor position. The characters cycle in the sequence shown
" See OPower Saving Function� for details about configuring Power Saving settings.below.
" The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all modes.Press D.
" The day of the week is automatically displayed in accordance with the date (year,x0 to 9(space)
month, and day) settings.Press B.
Telememo8. When the character you want is at the cursor position, press C to move the cursor
The Telememo Mode lets you store up to 30 records, each containing name andto the right.
telephone number data. Records are automatically sorted based on the characters of9. Repeat steps 7 and 8 until you complete number input.
the name. You can recall records by scrolling through them on the display." You can input up to 12 digits for the number.
10.After inputting your data, press A to store it.
Remaining memoryTelephone number" After data storage is complete, the cursor appears in the name area of the
display, ready for input of a new Telememo record.
11.Input more data (starting from step 3) or press A again to return to the Telememo
record screen (without the cursor).
" The name can show only three characters at a time, so longer text scrolls
Alternate atcontinuously from right to left. The last character is indicated by the symbol after it.
two-second
intervalTo recall Telememo records
NameIn the Telememo Mode, use D (+) and B (�) to scroll through Telememo records on
the display.
" See OSort Table� for details on how the watch sorts records.
" Pressing D while the last Telememo record is on the display or B while the first
" All of the operations in this section are performed in the Telememo Mode, which yourecord is on the display displays the new data screen.
enter by pressing C.
1 |
ACEC
