TELEMEMO MODETo edit Telememo data items
1. In the Telememo Mode, scroll through the data items and display the one you want to
Remaining memoryThe Telememo Mode lets you store up to 30edit.
pairs of name and telephone number data.2. Press A and a cursor appears in the animation area.
Data is automatically sorted based on the3. Use M to move the flashing to the character you want to change.
characters of the name. You can recall data by4. Use B to change the character.
scrolling through it on the display.For details on inputting characters, see OTo input new Telememo data� (steps 3 for
MSee the OCHARACTER LIST� for details onname input and 7 for number).
SIG ALMhow the watch sorts data.A5. After making the changes that you want, press A to store them and return to the
The new data screen appears when there isTelememo Mode data screen.
Name
no data stored in memory, or when you scroll
to the location between the last and the first
Telephonedata items stored in memory.To delete Telememo data
numberSIG ALM1. In the Telememo Mode, scroll through the data items and display the one you want to
The data item on the display when you exit
delete.
Bthe Telememo Mode appears first the next2. Press A and a cursor appears in the animation area.
time you enter the Telememo Mode.3. Hold down B and M at the same time until the message CLR (clear) appears in the
SIG ALMIf you do not operate any button for a fewanimation area.
minutes while in the Telememo Mode, the
[New Data Screen]watch automatically goes back to theAt this time the cursor appears in the animation area, ready for input.
4. Input data or press A to return to the Telememo Mode data screen.
Timekeeping Mode.
To input new Telememo data
Animation area1.In the Telememo Mode, press B until the new data screenSTOPWATCH MODE
appears.
CursorThe Stopwatch Mode measures elapsed time and
MIn the Telememo Mode, the animation area of the display1/100 second
is used for name input and display.cumulative elapsed time. The range of the stopwatch is 23
AIf the message FULL appears in the number area of thehours, 59 minutes, 59.99 seconds.M
display, it means that memory is full. To store more data,
A
you will first have to delete some of the data stored inTo measure elapsed time
memory.1. Press B to start the stopwatch.
2. Press B to stop the stopwatch.
SIG ALM2. Press A and a cursor appears in the animation area.3. Press A to clear the stopwatch to all zeros.
3. Use B to change the character at the cursor position inInstead of pressing A, you can also clear the stopwatch
the animation area. The character changes in the followingBSIG ALMby holding down B for a few seconds.
sequence.
Number areaB
Hours
Seconds
(space)A to Z t o9 .-
Minutes
To measure cumulative elapsed time
Holding down B changes the character at high speed.
4. When the character you want is at the cursor position, press M to move the cursor to1. Press B to start the stopwatch.
2. Press B to stop the stopwatch.the right.
3. Press B again to resume timing from the time shown on the display.
5. Repeat the steps 3 and 4 until your text is complete.
You can repeat steps 2 and 3 as many times as you like.
You can input up to eight characters for the name.
4. Press A to clear the stopwatch to all zeros.
6. After you input a name, use M to move the cursor to the number area.
There are eight spaces provided for input of characters of each name, though onlyInstead of pressing A, you can also clear the stopwatch by holding down B for a few
seconds.
three characters are visible at a time in the animation area. If the name you input has
less than eight characters, use M to move the cursor to the eighth space (which
means you would press M three times after inputting a 5-character name, for example).
Pressing M again while the cursor is at the eighth space causes it to jump down to theALARM MODE
first digit in the number area. When the cursor is at the 12th digit of the number area,
pressing M causes it to jump back up to the first character of the name.AM indicatorWhen the Daily Alarm is turned on, the alarm sounds for 20
7. Use B to change the character (hyphen, number, or space) at the cursor position inseconds at the preset time each day. Press any button to
Hour : Minutesstop the alarm after it starts to sound.
the number area. The character changes in the following sequence.
MWhen the Hourly Time Signal is turned on, the watch beeps
-0 to 9(space)every hour on the hour.A
To set the alarm time
Holding down B changes the character at high speed.1. Press A while in the Alarm Mode. The hour digits flash
8. When the character you want is at the cursor position, press M to move the cursor toAon the display because they are selected.
the right.?
This operation automatically turns on the Daily Alarm.
9. Repeat steps 7 and 8 until you complete number input.SIG ALM2. Press M to change the selection in the following
You can input up to 12 digits for the number.sequence.
10.After inputting your data, press A to store it and return to the Telememo Mode dataB
screen (without the cursor).Alarm onHourMinutes
indicatorIf you do not perform any button operation for few minutes while the cursor is on the
display, the watch automatically returns to the Telememo Mode data screen.Hourly time signal
on indicator
The animation area of the display can show only three characters at a time, so longer
text scrolls continuously from right to left.3. Press B to increase the selected digits. Holding down B increases the selection at
The number area can show up to six digits at one time. If a number has more than sixhigh speed.
digits, the display automatically switched between the first six digits (counting forwardThe format (12-hour and 24-hour) of the alarm time matches the format you select for
from the first digit) and the last six digits (counting backward from the last digit) of thenormal timekeeping.
number. This means that if a number is 12 digits long, the number area switchesWhen setting the alarm time using the 12-hour format, take care to set the time correctly
between the first six digits and the last six digits. If a number is seven digits long, theas a.m. (A indicator) or p.m. (P indicator).
number area switches between digits 1 through 6, and digits 2 through 7.4. After you set the alarm time, press A to return to the Alarm Mode.
If you do not operate any button for a few minutes while a selection is flashing, the
Animation AreaNumber Areaflashing stops and the watch goes back to the Alarm Mode automatically.
03-3347-4811
Separator To turn the Daily Alarm and Hourly Time Signal on and off
(inserted automatically)Press B while in the Alarm Mode to change the status of the Daily Alarm and HourlySIG ALMSIG ALM
Time Signal in the following sequence.
03-123-45
[Alarm On Indicator/Hourly Time Signal On Indicator]
Last letter of textSIG ALMJSIG ALMHSIG ALMSIG ALMHJSIG ALMSIG ALM
Both ONBoth OFFDaily AlarmHourly Time
To recall Telememo dataOnlySignal Only
In the Telememo Mode, press B to scroll forward through stored data items.
Holding down B scrolls through the data at high speed.To test the alarm
Hold down B while in the Alarm Mode to sound the alarm.
- 3 - |
ACEC
