1623 1667 1668 1678 1807 1808 1809 1852
1853 1854 1855 1891 1932 1952 1955GOMIX(E)-1
GENERAL GUIDE
?The configuration of this watch may differ somewhat from that shown in the illustration.
?Press CCCCC to change from mode to mode.
?In any mode, press DDDDD to illuminate the display for about two seconds.
?The animated figures perform a variety of different actions, depending on the mode the watch is in.
Timekeeping ModeAlarm ModeStopwatch Mode
TIMEKEEPING MODETo set the alarm time
1.Hold down AAAAA while in the Alarm Mode. The hour digits flash on the display be-
DateDay of the week?Use EEEEE to switch the display between month/datecause they are selected.
and date/day of the week.?At this time the Daily Alarm is switched on automatically.
?Press BBBBB to play a melody for about 10 seconds.2.Press CCCCC to change the selection in the following sequence.
Pressing any key while a melody is play stops the
melody. The melody that plays depends on when
you press BBBBB.HourMinutesAlarm Sound
Hour3.Press EEEEE to increase the selected digits and BBBBB to decrease them. Holding down
either button changes the selection at high speed.
PMMinutes Seconds?The format (12-hour and 24-hour) of the alarm time matches the format you select
indicatorfor normal timekeeping.
?When setting the alarm time using the 12-hour format, take care to set the time
To set the time and datecorrectly as morning or afternoon.
1.Hold down AAAAA while in the Timekeeping Mode. The seconds digits flash on the4.After you set the alarm time, press AAAAA to return to the Alarm Mode.
display because they are selected.?If you do not operate any button for a few minutes while a selection is flashing, the
2.Press CCCCC to change the selection in the following sequence.flashing stops and the watch goes back to the Alarm Mode automatically.
?If you do not operate any button for a few minutes in the Alarm Mode, the watch
SecondsHourMinutesYeargoes back to the Timekeeping Mode automatically.
To switch the Daily Alarm and Hourly Time Signal on and off
12/24-HourDay ofPress EEEEE while in the Alarm Mode to change the status of the Daily Alarm and Hourly
DateMonth
Formatthe weekTime Signal in the following sequence.
3.While the seconds digits are selected (flashing), press EEEEE to reset the seconds toDaily AlarmHourly Time
O00�. If you press EEEEE while the seconds count is in the range of 30 to 59, it is resetBoth OFFonlySignal onlyBoth ON
to O00� and 1 is added to the minutes. If the seconds count is in the range of 00 to
29, the minutes count is unchanged.
4.While any other digits (besides seconds), are selected (flashing), press EEEEE to in-
crease the number or BBBBB to decrease it. Holding down either button changes theALM : Daily Alarm
current selection at high speed.SIG : Hourly Time Signal
?While the day of the week is selected, pressing EEEEE advances to the next day, while
pressing BBBBB returns to the previous day.To test the Alarm
?While the 12/24-hour setting is selected, press EEEEE to switch between the two for-Pressing BBBBB sounds the currently selected alarm sound.
mats.It takes about 10 seconds for the alarm sound to finish. You can stop it manually by
5.After you set the time and date, press AAAAA to return to the Timekeeping Mode.pressing any key.
?The date can be set within the range of January 1, 1995 to December 31, 2039.?Note that if 0 is set as the alarm sound, pressing BBBBB randomly selects one of the
?If you do not operate any button for a few minutes while a selection is flashing, themelodies. The sound that is randomly selected when the next alarm time is reached
flashing stops and the watch goes back to the Timekeeping Mode automatically.will probably be different from the one that sounds when you press BBBBB.
ABOUT THE BACKLIGHTSTOPWATCH MODE
?Pressing DDDDD at any time illuminates the display for about two seconds and causesHoursThe Stopwatch Mode lets you measure elapsed time,
an animated figure to appear. The type of animation that appears depends uponMode indicatorsplit times, and two finishes. The range of the stop-
when you press DDDDD.watch is 23 hours, 59 minutes, 59.99 seconds.
?The backlight of this watch employs an electro-luminescent (EL) light, which loses?Animated figures appear on the display while the
its illuminating power after very long term use.stopwatch is measuring an elapsed time.
?The watch will emit an audible sound whenever the display is illuminated. This is?If you do not perform any key operation while in
caused by a transistor that vibrates when the EL panel lights up. It does not indicatethe Stopwatch Mode, the watch automatically re-
malfunction of the watch.turns to the Timekeeping Mode (except when an
elapsed time measurement is in progress.
To measure elapsed time
Minutes1.Press EEEEE to start the stopwatch.
ALARM MODE
2.Press EEEEE to stop the stopwatch.
Seconds
Hourly timeThis watch include three built-in melodies, which you?You can resume the measurement operation by
signal onCur-Alarm oncan use in any of the following five settings to sound1/100 seocndpressing EEEEE again.
indicatorrentindicatorwhen an alarm time is reached.3.Press BBBBB to clear the stopwatch to all zeros
time Mode indicator(0H00O00�00).
SettingAlarm Sound
0.Random play of melodies 1, 2, and 3To record split times
1.Melody 11.Press EEEEE to start the stopwatch.
2.Melody 22.Press BBBBB to display the timing up to that point. Stopwatch timing continues internal-
3.Melody 3ly.
4.Beeper3.Press BBBBB to clear the split time and to continue time measurement on the display.
Hour?You can repeat steps 2 and 3 as many times as you want.
Minutes4.Press EEEEE to stop the time measurement.
5.Press BBBBB to clear the stopwatch to all zeros.
?See the MELODY LIST at the back of this manual for the names of melodies.
?When the Daily Alarm is switched on, the alarm sounds for about 20 seconds at the
preset time each day. Press any button to stop the alarm after it starts to sound.To time first and second place finishes
When the Hourly Time Signal is switched on, the watch beeps every hour on the1.Press EEEEE to start the stopwatch.
hour.2.Press BBBBB when the first finisher crosses the line, and record the time.
3.Press EEEEE when the seconds finisher crosses the line.
4.Press BBBBB to display the finishing time of the second finisher.
5.Press BBBBB to clear the stopwatch to all zeros. |
ACEC
