STOPWATCH MODEALARM MODE
Mode indicatorThe Stopwatch Mode lets you measure elapsed time, splitMode indicator � Alarm No.Five independent Daily Alarms can be set. Each alarm
times, and two finishes. You also get Auto-Start function.
Graphic arealets you set the hour and minutes. When the Daily Alarm
The range of the stopwatch is 59 minutes, 59.99 seconds.is turned on, the alarm sounds for 20 seconds at the pre-
In the Stopwatch Mode, press to illuminate the dis-set time each day. Press any button to stop the alarm
play for about three seconds.after it starts to sound.
When the Hourly Time Signal is turned on, the watch beeps
To measure elapsed timeevery hour on the hour.
1.Press to start the stopwatch.In the Alarm Mode (including alarm time setting), press
2.Press to stop the stopwatch. to illuminate the display for about three seconds.
MinutesYou can resume the measurement operation by press-The graphic area in the Alarm Mode shows the current
Secondsing again.on/off status of each of the five alarms.
1/100 second3.Press to clear the stopwatch to all zeros.Hour : Minutes
Alarm on indicator
To record split timesAM indicator
1.Press to start the stopwatch.
2.Press to display the timing up to that point. Stopwatch timing continues internally.
3.Press to clear the split time and to continue time measurement on the display.To set an alarm time
You can repeat steps 2 and 3 as many times as you want.1.Press while in the Alarm Mode to select the alarm whose time you want to set.
4.Press to stop the time measurement.
5.Press to clear the stopwatch to all zeros.Alarm 1Alarm 2Alarm 3Alarm 4
Hourly Time SignalAlarm 5
To time first and second place finishes
1.Press to start the stopwatch.2.After you select an alarm, hold down until the hour digits start to flash on the
2.Press when the first finisher crosses the line, and record the time.display. The hour digits flash because they are selected.
3.Press when the second finisher crosses the line.This operation automatically turns on the alarm.
4.Press to display the finishing time of the second finisher.3.Press to change the selection in the following sequence.
5.Press again to clear the stopwatch to all zeros.
HourMinutes
About the Auto-Start function
With the Auto-Start function, the watch performs a 5-second countdown. When the4.Press to increase the selected digits. Holding down changes the selection at
countdown reaches zero, stopwatch operation starts automatically. During the final
high speed.
three seconds of the countdown, a beeper sounds with each second.The format (12-hour and 24-hour) of the alarm time matches the format you select
for normal timekeeping.
To use the Auto-Start functionWhen setting the alarm time using the 12-hour format, take care to set the time
1.While the stopwatch display is showing all zeros correctly as a.m. (A indicator) or p.m. (P indicator).
() in the Stopwatch Mode, press .
At this time the auto-startindicator appears on the dis-5.After you set the alarm time, press to return to the Alarm Mode.
play to indicate that auto-start is on. Press again toIf you do not operate any button for a few minutes while a selection is flashing, the
turn auto-start off (indicated when the auto-start indica-
flashing stops and the watch goes back to the Alarm Mode automatically.
tor is not on the display).
2.Press to start the countdown.To turn an alarm and the Hourly Time Signal on and off
Pressing also causes the countdown time to appear1.In the Alarm Mode, press to select an alarm or
G-SHOCK mark
on the display.the Hourly Time Signal.
Graphic area2.Press to toggle the select item on and off.Auto-start indicator
When the countdown reaches zero, a tone sounds, the backlight illuminates theThe indicators ALM and appear on the display
display, and a stopwatch timing operation starts automatically.whenever an alarm is turned on.
To stop the Auto-Start countdown and return to the all-zeros display, press .The indicators SIG and appear on the display
Pressing while the Auto-Start countdown is in progress immediately start thewhenever the Hourly Time Signal is turned on.
stopwatch.Indicators in the graphic area of the Alarm Mode
show which alarms are turned on.
In other modes (besides the Alarm Mode), the ALM
indicator remains on the display as long as at least
Alarm on indicatorone of the alarms is on, while the SIG indicator re-
Alarm 2 (off) Alarm 5 (off)mains on the display while the Hourly Time Signal
is on.
Alarm 4 (off)To test the alarmAlarm 1 (on)
Hold down while in the Alarm Mode to sound the
Alarm 3 (on)alarm.
- 3 - |
ACEC
