USEROS GUIDE 2611
To use the countdown timer
In the Countdown Timer Mode, press D to start the" The snooze alarm on indicator ( ) flashes during the 5-minute intervals between
countdown timer.alarms.
" The countdown timer measurement operation continues" Displaying the Alarm 1 setting screen while the snooze alarm is turned on
even if you exit the Countdown Timer Mode.automatically turns off the snooze alarm (making Alarm 1 a one-time alarm).
" The table below describes button operations you can
perform to control countdown operations.To turn the hourly time signal on and off
1.In the Alarm Mode, use D to select the Hourly Time
Signal.
To do this:Do this:2.Press B to toggle it on and off.
" Turning on the Hourly Time Signal displays the hourly
Stop the countdown operationPress D.time signal on indicator ( ) on its screen.
Resume a stopped countdown operationPress D again." The hourly time signal on indicator is displayed in all
modes.
Display the countdown start timeWhile the countdown is
stopped, press B.
Hourly time signal on
Stop the countdown operation and display the reset timePress B.indicator
Start the countdown from the displayed reset timePress D.
" The table below describes button operations you can perform during an elapsedStopwatch
time measurement operation in the elapsed time mode.
The stopwatch lets you measure elapsed time, split times,
To do this:Do this:Minutesand two finishes.
Stop the elapsed time operationPress D.Seconds" The display range of the stopwatch is 59 minutes, 59.99
seconds.
Resume a stopped elapsed time operationPress D again." The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
Display the countdown start timeWhile the elapsed time is
" The stopwatch measurement operation continues even
stopped, press B.
if you exit the Stopwatch Mode.
Stop the elapsed time operation and display the reset timePress B." Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
Start the countdown from the displayed reset timePress D.
elapsed time measurement.
1/100 Second" All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing C.
Alarms
To measure times with the stopwatch
Alarm timeYou can set five independent Daily Alarms. When an
(Hour : Minutes)alarm is turned on, the alarm tone sounds when the alarmElapsed Time
time is reached. One of the alarms can be configured as a
snooze alarm or a one-time alarm, while the other four areD¤D¤D¤D¤B
one-time alarms.StartStopRe-startStopClear
You can also turn on an Hourly Time Signal that causes
the watch to beep twice every hour on the hour.Split Time
" There are five alarm screens numbered 1 through 5.D¤B¤B¤D¤B
The hourly time signal screen is indicated by :00.StartSplitSplit releaseStopClear
Alarm number" When you enter the Alarm Mode, the screen you were(SPL displayed)
viewing when you last exited the mode appears first.
SNZ" All of the operations in this section are performed in theTwo Finishes
Alarm Mode, which you enter by pressing C.DB¤D¤B¤B
¤
To set an alarm timeStartSplitStopSplit releaseClear
1.In the Alarm Mode, use D to scroll through the alarmFirst runnerSecond runnerDisplay time of
screens until the one whose time you want to set isfinishes.Display time offinishes.second runner.
displayed.first runner.
x1x2x3
Backlight
The backlight uses an EL (electro-luminescent) panel that
:00x5x4causes the entire display to glow for easy reading in the
Auto light switch
dark. The watchOs auto light switch automatically turns on
on indicator
" You can configure Alarm 1 as a snooze alarm or a one-time alarm. Alarms 2the backlight when you angle the watch towards your face.
through 5 can be used as one-time alarms only." The auto light switch must be turned on (indicated by
" The snooze alarm repeats every five minutes.the auto light switch on indicator) for it to operate.
2. After you select an alarm, hold down A until the hour setting of the alarm time" See OBacklight Precautions� for other important
starts to flash. This indicates the setting screen.information about using the backlight.
" This operation automatically turns on the alarm.
3. Press C to move the flashing between the hour and minute settings.To turn on the backlight manually
In any mode, press L to illuminate the display for about
4. While a setting is flashing, use D (+) and B (�) to change it.
" When setting the alarm time using the 12-hour format, take care to set the timeone second.
correctly as a.m. (no indicator) or p.m. (P indicator)." The above operation turns on the backlight regardless of
the current auto light switch setting.
5. Press A to exit the setting screen.
About the Auto Light Switch
Alarm OperationTurning on the auto light switch causes the backlight to turn on for about one second,
The alarm sounds at the preset time for about 10 seconds. In the case of the snoozewhenever you position your wrist as described below in any mode. Note that this
alarm, the alarm operation is performed a total of seven times, every five minutes, orwatch features a OFull Auto EL Light,� so the auto light switch operates only when
until you turn the alarm off or change it to a one-time alarm.available light is below a certain level. It does not turn on the backlight under bright
Notelight.
" Pressing any button stops the alarm tone operation.
" Performing any one of the following operations during a 5-minute interval betweenMoving the watch to a position that is parallel to the ground and then tilting it towards
snooze alarms cancels the current snooze alarm operation.you more than 40 degrees causes the backlight to turn on.
Displaying the Timekeeping Mode setting screen
Displaying the Alarm 1 setting screen
To test the alarmParallel toMore than
In the Alarm Mode, hold down D to sound the alarm.ground40°
To turn Alarms 22222 through 55555 on and off
1.In the Alarm Mode, use D to select a one-time alarm
(alarm number 2 through 5).
2.Press B to toggle the displayed alarm on and off.
" Turning on a one-time alarm (2 through 5) displays theWarning!
one-time alarm on indicator () on its screen." Always make sure you are in a safe place whenever you are reading the
" The one-time alarm on indicator is displayed in alldisplay of the watch using the auto light switch. Be especially careful when
modes.running or engaged in any other activity that can result in accident or injury.
" If any alarm is on, the alarm on indicator is shown onAlso take care that sudden illumination by the auto light switch does not
One-time alarm onthe display in all modes.surprise or distract others around you.
indicator" When you are wearing the watch, make sure that its auto light switch is turned
off before riding on a bicycle or operating a motorcycle or any other motor
To select the operation of Alarm 11111vehicle. Sudden and unintended operation of the auto light switch can create a
1. In the Alarm Mode, use D to select Alarm 1.distraction, which can result in a traffic accident and serious personal injury.
2. Press B to cycle through the available settings in the sequence shown below.
To turn the auto light switch on and off
Snooze alarm on indicator ( ) and one-time alarm on indicator ( ) In the Timekeeping Mode, hold down D for about two seconds to toggle the auto light
switch on ( displayed) and off ( not displayed).
" The auto light switch on indicator ( ) is on the display in all modes while the auto
light switch is turned on.
One-time alarm onSnooze alarm onAlarm off
" The applicable alarm on indicator ( or ) is displayed in all modes when an
alarm is turned on.
3 |
ACEC
