MO0302-A
USEROS GUIDE 2611
Getting Acquainted
Warning!
Congratulations upon your selection of this CASIO watch. To get the most out of your" The longitude, lunitidal interval, Moon phase indicator and tide graph data that
purchase, be sure to carefully read this manual and keep it on hand for later referenceappear on the display of this watch are not intended for navigation purposes.
when necessary.Always use proper instruments and resources to obtain data for navigation
purposes.
Expose the watch to bright light to charge its battery before using it." This watch is not an instrument for calculating low tide and high tide times. The
tide graph of this watch is intended to provide a reasonable approximation of tidal
You can use this watch even as its battery is being charged by exposure to bright
movements only.
light.
" Be sure to read OBattery� of this manual for important information you need to" CASIO COMPUTER CO., LTD. assumes no responsibility for any loss, or any
claims by third parties that may arise through the use of this watch.
know when exposing the watch to bright light.
If the display of the watch is blank...About This Manual
If the P.SAVE indicator is flashing on the display, it means" Button operations are indicated using the letters shown
that the display is blank because the watchOs Powerin the illustration.
lllllllllllllllSaving function has turned off the display to conserve" Each section of this manual provides you with the
power. Power Saving automatically turns off the displayinformation you need to perform operations in each
and enters a sleep state whenever your watch is left for amode. Further details and technical information can be
certain period where it is dark.found in the OReference� section.
" The initial factory default setting is Power Saving on.
" The watch recovers from the sleep state if you move it to
a well-lit area, if you press any button, or if you angle the
watch towards your face for reading.
" See OPower Saving Function� for more information.(Light)
General Guide
" Press C to change from mode to mode.
Moon / Tide Data ModeWorld Time Mode
" In any mode, press L to illuminate the display.
Timekeeping Mode
Press C.
Countdown Timer
Stopwatch ModeAlarm ModeMode
Timekeeping
Use the Timekeeping Mode to set and view the current time and date.Home Site Data
Moon phase, tide graph data, and Moon/Tide Data Mode data will not be displayed
Month-Day ScreenDay of the Week Screenproperly unless Home Site data (GMT differential, longitude, and lunitidal interval) is
configured correctly.
Moon phase indicator" The GMT differential is the time difference of the time zone where the site is located
Tide graph
and Greenwich Mean Time.
PM indicatorPress B." The lunitidal interval is the time elapsing between the MoonOs transit over a meridian
and the next high tide at that meridian. See OLunitidal Interval� for more information.
" This watch displays lunitidal intervals in terms of hours and minutes.
" The OSite Data List� and OLunitidal Interval List� provide GMT differential, longitude,
and lunitidal interval information around the world.
Month � DayDay of week" The following is the initial factory default Home Site data (Tokyo, Japan) when you
Seconds Hour : Minutesfirst purchase the watch, whenever battery power drops to Level 4, and whenever
" The tide graph shows tidal movements for the current date in accordance with theyou have the battery replaced. Change these settings to match the area where you
current time as kept in the Timekeeping Mode.normally use the watch.
" The Moon phase indicator shows the current Moon phase in accordance with theGMT differential (+9.0); Longitude (East 140 degrees); Lunitidal interval (5 hours,
current date as kept in the Timekeeping Mode.20 minutes)
Important!To configure Home Site data
" Moon phase, tide graph data, and Moon/Tide Data Mode data will not be displayed1.In the Timekeeping Mode, hold down A until the
properly unless the Timekeeping Mode current date and time settings and Homeseconds start to flash, which indicates the setting
Site data are configured correctly. See OHome Site Data� for more information.llllllllscreen.l
ll2.Press A again to display the GMT differential setting
l
To set the time and datelllscreen.
l
1.In the Timekeeping Mode, hold down A until thelll3.Press C to move the flashing in the sequence shownlllll
seconds start to flash, which indicates the settingbelow to select other settings.
screen.
2.Press C to move the flashing in the sequence shownGMT differential
lllllllGMTLongitudeLunitidal Interval Lunitidal Interval below to select other settings.
llllll differentialHoursMinutes
SecondsDST on/offHourMinutes4. When the setting you want to change is flashing, use D and B to change it as
12/24-Hour
Formatdescribed below.
Power SavingDayMonthYear
SettingScreenButton Operations
GMT differentialUse D (+) and B (�) to change the setting.
3. When the setting you want to change is flashing, use D and B to change it as
" You can specify a value in the range of �11.0
described below.
to +14.0, in 0.5-hour unit.
To change this settingPerform this button operationLongitudeUse D (+) and B (�) to change the setting.
SecondsPress D to reset to 00." You can specify a value in the range of
179°W to 180°E, in 1-degree units.
DST on/offPress D to toggle between Daylight Saving Time
(ON) and Standard Time (OF).Lunitidal IntervalUse D (+) and B (�) to change the setting.
Hours, Minutes
Hour, Minutes, Year,Use D (+) and B (�) to change the setting.
Month, Day
5. Press A to exit the setting screen.
12/24-Hour FormatPress D to toggle between 12-hour (12H) and
24-hour (24H) timekeeping.
Power SavingPress D to toggle Power Saving on (ON) and offMoon/Tide Data
(OF).Moon/tide data lets you view the Moon age and Moon
Moon phase indicator
4. Press A twice to exit the setting screen.phase for a particular date, and tidal movements for a
" The first press of A displays the GMT differential setting screen. Pressing A againparticular date and time for the Home Site.
exits the setting screen." If you suspect that the Moon/tide data is not correct for
" See OPower Saving Function� for details about configuring Power Saving settings.some reason, check the Timekeeping Mode data
" The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is(current time, date, and Home Site settings), and make
applied in all modes.changes as required.
" The day of the week is automatically displayed in accordance with the date (year," See OMoon Phase Indicator� for information about the
month, and day) settings.Moon phase indicator and OTide Graph� for information
about the tide graph.
" All of the operations in this section are performed in the
Moon ageMoon/Tide Data Mode, which you enter by pressing C.
1 |
ACEC
