1910-6
WORLD TIME MODETurning the Daily Alarm and Hourly Time Signal On
and Off
The World Time Mode shows the current time in 27 cities (29 time zones)The Daily Alarm and Hourly Time Signal sound only while they are turned on.
around the world, along with the current time in your home city (Home Time).
To turn the Daily Alarm and Hourly Time Signal on and off
Entering the World Time ModeIn the Alarm Mode, press the key to cycle through the on and off settings
as shown below.
In the Timekeeping Mode, press the key three times to enter the World
Time Mode. [Alarm ON Indicator / Hourly Time Signal ON Indicator]
City code GMT differentialHome time differential
Alarm OnAlarm OffAlarm OnAlarm Off
Press .Signal OnSignal OffSignal OffSignal On
AB
WORKHOME FAX CALL E-MAIL OTHERWORKHOME FAX CALL E-MAIL OTHER
Time in indicated citySTOPWATCH MODE
" In the World Time Mode, pressing toggles the upper part of the displayWith the Stopwatch Mode, you can measure elapsed time, split times, and two
between GMT differential (time difference between GMT and the displayedfinishes. The range of the stopwatch is 23 hours, 59 minutes, 59.99 seconds.
zone) and Home Time differential (time difference between your Home
Time and the displayed zone).
" See OWorld Time Mode Timekeeping� for details about city codes, GMTEntering the Stopwatch Mode
differential, and technical information about the World Time Mode.
In the Timekeeping Mode, press the key
Hoursfive times to enter the Stopwatch Mode.
Viewing the Time in Another City
In the World Time Mode, press to scroll forward through the city codesUsing the Stopwatch
and to scroll back.
The and keys are used to control
" City codes scroll in the sequence shown in the OCITY CODE TABLE�.
stopwatch operations as shown below.
WORKHOME FAX CALL E-MAIL OTHER" Note that the and keys are disabled
while the backlight is lit.
Daylight Saving Time (DST)
Minutes1/100 second
Hold down the key for two seconds to toggle the displayed time zone
between Daylight Saving Time (Summer Time) and Standard Time. TheSeconds
indicator DST on the display indicates that the zone is set for Daylight Saving
Time.(a) Elapsed Time
" Daylight Saving Time automatically advances the time setting by one hour
from Standard Time.
" You can make individual Daylight Saving Time settings for each time zone.StartStopRe-startStopClear
(b) Split Time
ALARM MODEStartSplitSplit releaseStopClear
(c) Two Finishes
You can use the Alarm Mode to set a Daily Alarm that sounds at the same
time each day, while turned on. You can also turn on an Hourly Time Signal
that causes the watch to beep twice every hour on the hour.StartSplitStopSplit releaseClear
First runnerSecond runner finishes. Record time of
finishes.Record time of firstsecond runner.
Entering the Alarm Mode
runner.
In the Timekeeping Mode, press the key four times to enter the Alarm Mode.
Setting the Daily Alarm Time
TIME AND DATE SETTINGS
Use the following procedure to set the time that you want the Daily Alarm to
sound each day.
Use the procedures described in this section to set the time and date after the
battery is replaced.
To set the Daily Alarm
1. In the Alarm Mode, hold down the A
button for two seconds until the hour digitsCalibrating the Seconds Count
of the alarm time start to flash on the
Use the following procedure to calibrate the seconds count on a time signal
display.from a radio, TV, or other source.
2. Use and to change the hour
ABsetting.
To calibrate the seconds count
WORKHOME FAX CALL E-MAIL OTHER" When setting the alarm time using the 12-
hour format, take care to set the time1. In the Timekeeping Mode, hold down the
Alarm on indicatorcorrectly as am (no indicator) or pm (PA button for two seconds, until the
seconds digits start to flash on the display.
indicator).
Hourly time signal on" The seconds digits are flashing because
3. Use the or keys to move the
indicatorthey are selected.
flashing to the minutes digits.
AB2.Press the key to set the seconds count
4. Use the and keys to change the
minutes setting.WORKHOME FAX CALL E-MAIL OTHERto 00 when the time signal you are
5. After the alarm time is the way you want it,calibrating to sounds.
press the A button to return to the Daily" Pressing while the seconds count is in the range of 30 to 59 resets the
Alarm display screen.seconds to 00 and adds 1 to the minutes. If the seconds count is in the
range of 00 to 29, the minutes count is unchanged.
3. Press the A button to return to the current time display.
Daily Alarm Operation
The alarm sounds at the preset time each day for about 20 seconds, or until
you stop it by pressing any button or key.Setting the Clock
Use the following procedure to select a city as your Home Time City, and then
To test the alarmset its time and date. You can also specify whether you prefer to use 12-hour
In the Alarm Mode, hold down the key to sound the alarm.or 24-hour timekeeping for all screens that show times.
Important!
Changing the city setting usually changes the time setting and sometimes
changes the date setting. Because of this, you should select your Home Time
City before setting the time and date. |
ACEC
