3.Use A and B to change the character at the cursor position in the text field. TheTo set the alarm time
character changes in the following sequence.1.Hold down C while in the Alarm Mode until the hour digits start to flash on the
display. The hour digits flash because they are selected.
Press BThis operation will turn the Daily Alarm on automatically.
(space)toto2.Press D to change the selection in the following sequence.
Press A
HourMinutes
Holding down either button changes the character at high speed.
4.When the character you want is at the cursor position, press D to move the cursor3.Press B to increase the selected digits or A to decrease them. Holding down
to the right.either button changes the selection at high speed.
5.Repeat steps 3 and 4 until your text is complete.The format (12-hour and 24-hour) of the alarm time matches the format you select
You can input up to eight characters in the text field.for normal timekeeping.
6.After you input a name, use D to move the cursor to the number field.When setting the alarm time using the 12-hour format, take care to set the time
The NAME indicator is cleared and the TEL indicator appears when the cursor is incorrectly as morning (no indicator) or afternoon (PM ).
the number input field.4.After you set the alarm time, press C to return to the Alarm Mode.
You can input up to eight characters for the name. After you input the eighth char-If you do not operate any button for a few minutes while a selection is flashing, the
acter, pressing D causes the cursor to jump to the first digit of the number.flashing stops and the watch goes back to the Alarm Mode automatically.
You can input up to 12 digits for the number. After input the twelfth digit, pressing D
causes the cursor to jump back to the first character of the name.To turn the Daily Alarm and Hourly Time Signal on and off
7.Use A and B to change the character (space, number, or hyphen) at the cursorPress B while in the Alarm Mode to change the status of the Daily Alarm and Hourly
position in the number field. The character changes in the following sequence.Time Signal in the following sequence.
Press B[Alarm ON Indicator/Hourly Time Signal ON Indicator]
(space)to
Press A
Holding down either button changes the character at high speed.Both ONBoth OFFDaily Alarm Hourly Time
8.When the character you want is at the cursor position, press D to move the cursorOnlySignal Only
to the right.
9.Repeat steps 7 and 8 until you complete number input.
You can input up to 12 digits in the number field.To test the alarm
10.After inputting your data, press C to store it.Hold down B while in the Alarm Mode to sound the alarm.
When you press C to store data, the watch takes a few seconds to sort memory
data. After the sort operation is complete, the watch returns to the normal Data
Bank Mode (without the cursor).STOPWATCH MODE
Unused spaces at the end of the name and number fields are automatically filled in
with O
t � whenever the number of characters you input in these fields is less thanMode indicatorThe Stopwatch Mode lets you measure elapsed time, split
the allowable maximum (8 characters for the name, 12 digits for the number). Thesetimes, and two finishes. The range of the stopwatch is 59
filler characters also appear on the display whenever you recall data.minutes, 59.99 seconds.
If you do not perform any button operation for a few minutes while the cursor is on
the display, the watch automatically returns to the normal Data Bank Mode (without
the cursor).
To recall Data Bank data
1.In the Data Bank Mode, press B to scroll through stored data items.
Holding down B scrolls through the data at high speed.
Only name data appears when you are scrolling through stored data items.
2.Press C to toggle the screen between the name and number data.
[Name Screen]Minutes1/100 second[Number Screen]
Seconds
Press C
(a) Elapsed time measurement
StartStopRe-startStopClear
NAME indicatorTEL indicator
The name and number scroll from right to left on the screen. A separator (<) is(b) Split time measurement
inserted between the last character and first character of the data.
To edit Data Bank data itemsStartSplitSplit releaseStopClear
1.In the Data Bank Mode, scroll through the data items and display the one you want
to edit.(c) Split time and 1st-2nd place times
2.Hold down C until the first character of the name starts to flash on the display.
3.Use D to move the flashing to the character you want to change.
4.Use A and B to change character.StartSplitStopSplit releaseClear
For details on inputting characters, see OTo input new Data Bank data� (steps 3 forFirst runner Second runner Record time of
name input and 7 for number).finishes.finishes.
second runner.
5.After making the changes that you want, press C to store them and return to theRecord time of
first runner.
Data Bank Mode.
To delete Data Bank data
1.In the Data Bank Mode, scroll through the data items and display the one you wantAUTO DISPLAY FUNCTION
to delete.The Auto Display function of this watch continually chang-
2.Hold down C until the first character of the name starts to flash on the display.es the contents of the digital display. Note that you can-
3.Press A and B at the same time to delete the data item.not use any of the watch's other functions (except for back-
At this time the cursor appears on the display, ready for input.light) while the Auto Display function is operating.
4.Input data or press C to return to the Data Bank Mode.
To turn the Auto Display off
Hold down D for about three seconds until the watch
ALARM MODEbeeps.
Mode indicatorWhen the Daily Alarm is turned on, the alarm sounds for
To turn Auto Display on
Hour : Minutes20 seconds at the preset time each day. Press any button
to stop the alarm after it starts to sound.
On-screen button labelsHold down D for about three seconds until the watch
When the Hourly Time Signal is turned on, the watch beeps
beeps.
every hour on the hour.
Note
The alarm sounds whenever the time displayed in the The Auto Display function cannot be performed while you are making settings (i.e.
Timekeeping Mode reaches the alarm time and the Hour-
while digits or other settings are flashing on the display).
ly Time Signal sounds at the top of each hour, regard-
less of whether you are using the Home Time screen or
About On-screen Button Labels
Dual Time screen.
Note that switching between the Home Time and DualThis watch features on-screen button labels that indicate the function of each button.
You can use the following procedure to turn these labels on and off.
Time screen in the Timekeeping Mode has no effect on
the Daily Alarm time setting. If you set an alarm time of
To turn on-screen button labels on and off
Alarm on indicator4:00 pm for your Home Time and then change to the
While the Auto Display function is turned on, press C to toggle the on-screen button
Dual Time screen, the Daily Alarm will start to sound
labels on and off.
Hourly time signalwhen the Dual Time reaches 4:00 pm.The on-screen button label setting you select remains in effect even when you turn
on indicator
off the Auto Display function.
- 3 - |
ACEC
